Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Cant access motor compartment

\015 Model 116.2421590 Found 2 screws to access motor compartment. Other 2 screws seem 2 be hidden under stop/start button. Can't access.\015

Answers :

Those screws are hidden under the plastic that you press to make the cord retract.The way I get into that area is to pry it up from the side of the cord retract panel.They take a fair amount of leverage to get it off but it is straightforward from there-Good Luck,
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cant access motor compartment

Those screws are hidden under the plastic that you press to make the cord retract.The way I get into that area is to pry it up from the side of the cord retract panel.They take a fair amount of leverage to get it off but it is straightforward from th ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Where are screws located that access main motor compartment in panasonic canister MC-V9647? Something is rattling inside and smells hot. Belt or motor?

If the model is the same as pictured, the screws should be visible. If the model is older like I think it is, the screws are going to be a tad tough to get to, but not impossible. First you will need to take the bag door off. Open i ... Panasonic Kenmore Canister Vacuum Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?

Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??

... Eureka Capture Upright Vacuum Vacuum

Motor problem I just picked up a screw. It appears to be stuck in motor. The sound of the motor changed to a whirring noise and it started to smoke. How can i access the motor?

First six pictures HERE will let you know how to remove shell to see the motor. I would not recommend starting it before you get the screw out (you will need to ... Kirby Generation 3 Bagged Upright Vacuum

Problem with motor; need to open the motor compartment

This may help. My Kenmore is ten years old. I found two screws under the hinges of the cover to the tool accessory compartment. Remove cover screws are in the corners. The other two I found are under the cord return foot pad. Pad pops off by pry ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Need to access motor on Volta Ultima 2000W vacuum cleaner

... Electrolux Guardian Bagged Canister Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

BURNING SMELL My DC 07 has suffered from poor suction in the upright position for some time now but this morning it ground to a halt. It was if the motor had burned out. I turned it upside down and some small stones etc tumbled out. I tried switching on again and the motor kicked in but the smell was horrendous so i switched off immediately. If it's likely to be **** inside the motor area i don't no how to access it. I've removed for fixing screws but still unable to prise apart. Is it just the

Hi.\015\012\015\012Try this site http://dysonmanuals.llc.nu/ has service manuals covering removing the Dc07 motor. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Motor still runs--sounds like jet engine. do I need a new motor? or is there some sort of muffler that has malfunctioned? vacuum belongs to disabled mom---so trying to do work ourselves--cant afford much. dont see anything obviously wrong--but know nothing about electric motors.

This little vac I think is actually made by Samsung. If it is ROARING and vibrating, either the bearings or suction fan is in bad shape. Remove the lid as if to inspect the belt and see if there is a visible intake opening with a plastic fan rotatin ... Bissell 3590 CleanView Bagless Upright Vacuum

Smoke from Hoover Savvy U8185-900. Looks to be from the Motor assembly U8174-900. How to access motor in order to verify condition, have already removed all screws, but unabale to expoxe motor..

... Hoover U8185-900 Upright Vacuum

How do I gain access to the motor of an Electrolux 2000 canister vacuum. The air intake on the motor must be partially blocked as there is a loss of suction and the motor makes that high pitched whine like it does when you cover the hose with your hand

Dismantling the vacuum probably won't help much, and reassembling can be a bear. \015\012To check the intake, remove bag and look into bottom of bag well. It there's a filter there, remove it and check intake at bottom of bag well. Clear if t ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a TriStar LEC vacuum and today I turned it on and for a split second the motor whirred and then nothing. Now it won't come on at all. I cannot find any way to access the motor.

How do i replace the power cord on my lec tristar vaccum? ... Tristar Vacuums

My Miele Solution HEPA 5000 vacuum cleanr gives off a burning smell but will continue to run with a varying motor tone. I have not run it for more than a minute like this. I have reviewed responses to similar problems but cannot figure out how to access the motor. Can anyone advise?

... Miele S318 Bagged Canister Vacuum

Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.

Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How do you replace a belt on the a Simplicity Synergy vaccuum? Removing the 2 screws on the bottom plate allows you to access the roller, but doesn't give you access to the drive motor. Any ideas?

... Simplicity 7850 Premier Bagged Canister Vacuum

How to open motor compartment to check motor on Kenmore canister vacume cleaner model 8120

... Kenmore Vacuums

Oreck xl9300 Bought a new motor but cant figure how to pull off the metal fan from the old motor. Is it muscle or a trick?

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=19810&thid=767429\015\012Oreck XL9300\015\012Posted by Cubfan70 on July 10, 2008\015\012Bought a new motor ... Oreck XL Ultra Bagged Upright Vacuum

Motor on mod 8975 making inordinate amount of noise disassembled 1 intake source at a time - still making noise can't figure out access to motor

The complete repair details and manuals for you bissel device is available on this link .\015\012\015\012 ... Bissell Vacuums

Need to change the motor on dc07 how do you get the motor out I have loosened and taken out all the screws and still cant disconnect the power cable in

Have you looked at www.dysonmedic.com ?\015\012\015\012It has a really good feature on changing a DC07 motor. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need to remove the top of the motor unit on a Kirby Generation 3 to access the motor area of the vacuum

First remove the back, then remove the handle assembly. Then pop off the plastic switch cover and it has one screw on the back you will need to take out, then there are two screws in the front of the body housing and two on the back that you will ne ... Kirby Generation 3 Bagged Upright Vacuum

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther

... Kenmore Vacuums

I want to take the fan impellar off the motor to clean it. I cant seem to get the metal housing off of the motor. Do you have to take the nut off the impellar If so how do you stop the shaft from turning thank you.

Very simply you dont take the fan out of the motor. it was not made to be removed or cleaned because its not supposed o get dirty if your using good bags in the vacuum. the best you can do is blow it out with an air hose. ... Electrolux Epic 6500 Vacuum

I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0429 seconds