Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Kenmore Canister Vacuum Model 116.23912300 Hose Connection Pipe (KC92PBZTZV06)

\015 The base of my hose connection pipe broke where it snaps into the body of the vacuum. I patched it with tape and it worked for a while, but now the whole vacuum has stopped working. Since the controls are on the hose, I think the problem is with the connector pipe. I have ordered the hose connection pipe (KC92PBZTZV06)...but don't know how to take the hose apart to install the new part.....Can you help me? I'm pretty handy, but there's a trick to this that I don't know.\015\012\015\012Number 10 on this diagram\015\012http://www.searspartsdirect.com/partsdirect/retrieveSubComponentPartsAction.action?modelNumber=11623912300&productCategoryId=0642000&brandId=0582&modelName=VACUUM&diagramPageId=00003&componentDescription=HOSE&documentId=P0412090&backToLink=Return%20to%20Sub%20Components%20list\015\012\015\012This is the part.\015\012http://www.searspartsdirect.com/partsdirect/displayPartDetailAction.action?partNumber=KC92PBZTZV06&productGroupId=0020&supplierId=116\015\012\015\012Thank you for your help!\015\012Stumped in Harrisburg PA\015

Answers :

To remove the cover. There are two tabs on the connection pipe that hold the hose connector onto the connection pipe, one on each side located on the section of the connection pipe just next to where it bends. They are visible under the lip of the cover if you gently pry up the cover on each side. You have to use two flat-bladed screwdrivers, one for each tab, and gently pry the cover over these tabs, working simultaneously on both tabs. The cover will then slip off onto the hose. Next, pull off the three wire connectors from the hose wires. After that you should be able to lift the hose wires out of the grooves they are in. There are also two latches on the connection pipe that help hold the hose on. Gently raise these without breaking them as you work off the hose. Remove the old hose from the connection pipe. Slip the new hose onto the connection pipe. The latches will hold the hose onto the connection pipe. Be sure you follow the color code on the wires to match the new hose wires to the connectors on the connection pipe. Push the wires back into the groves on the connection pipe. When everythings is sitting snugly against the connection pipe, you should be able to slip the hose connector cover back on the connection pipe and lock it over the two tabs.
\015\012
\015\012good luck.
\015\012rate the solution if helped by it.
\015\012feel free for further queries.
\015\012thanks
I put a tiny bit of liquid soap on the tabs and connection pipe flanges. I was then able to wiggle the tabs over the flanges.
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore Canister Vacuum Model 116.23912300 Hose Connection Pipe (KC92PBZTZV06)


To remove the cover. There are two tabs on the connection pipe that hold the hose connector onto the connection pipe, one on each side located on the section of the connection pipe just next to where it bends. They are visible under the lip of the co ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My Kenmore canister vacuum cleaner model 116.27514700 has unacceptably low suction.It is much less than my older GE Walmart canister vacuum. the 2 filters are very clean and there is no blockage in the hose and the dust collection bag is empty. Is poor suction a characteristic of this model or if not is there a way to fix this problem?


... Panasonic Kenmore Canister Vacuum Vacuum

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak


... Kenmore Progressive 35922 Bagged Upright Vacuum

Needed, a new Hose for Kenmore Canister Vacuum cleaner. Model Number 1162497184 --A 3.9 Powermate Kenmore Vacuum Cleaner


... Kenmore Vacuums

I bought a Kenmore canister vacuum, model 116, in April 2007. This morning, the sound of the motor suddenly began to deepen, and I began to lose suction. Normally, if something is clogging the hose, the motor will wind up to a higher pitch, not a lower one. The filters are clean, the bag is empty, and I can't detect anything lodged in the hose. If this were a car's engine, I would say it's "lugging down". Any pointers?


Okay, bear with me. Is it possible you have a suction adjustment, dial somewhere on vac. Check and see and if it does, be sure it's all the way up. Also, try removing hose and run a broom handle fr. one end to the other...BUT be careful not to stretc ... Vacuums

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony


... Kenmore Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks


Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

Kenmore progressive canister bad connection from hose to canister


It could be, the female part of the connector is stretched open. You can usually insert something, like a dart, between the sleeve and the holder, to tighten it. If you paid with Pay Pal, see about getting your money back. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Intuition Canister vacuum Hose connection


... Kenmore Vacuums

My kenmore progressive canister vacuum won't start,any ideas, is there a fuse? it was on then just quit. I've checked all connections and made sure they are snug, and that it's still plugged in (!) model 116.


Wire broken in several place along suction tubing. Replaced tubing and works fine ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Replace hose swivel on a kenmore canister vacuum model 21714


... Kenmore Vacuums

How to remove and replace hose on swivel of kenmore canister vacuum model 11621513002


... Kenmore 23313 Whispertone Bagged Canister Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

Replace hose on kenmore 3.9 canister vacuum - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore canister vacuum model #116 - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped


... Electrolux Guardian Bagged Canister Vacuum

I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.


... Kenmore EVO All Surface Floor Cleaner Vacuum

I need to replace the hose on my Euro Pro Shark canister vacuum EP722. After numerous searches, unable to find online. Looking for simular hose that will attachment to canister. What hose from another model or even maker will work? Thanks


Go to shark in GOGGLE. Go sharks wedsite, find your vaccum, click your hose. We have 3 mops and vacuum. No trouble getting parts and filters. Not high priced. ... Euro-Pro EP722 Canister Vacuum

Smoke coming out of my Kenmore Canister Vacuum Model 22550300C


Sounds like a motor err. Could be repaired by a professional but it never be as good as a new one. Also they you might not find anyone to repair it because the replacement motor might cost more than a new vacuum /considering it's age the motor will b ... Kenmore Vacuums

Replace connection pipe kenmore vacuum - Kenmore Vacuums


... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1202 seconds