Having problems with your Kenmore 25512/ 25513 Progressive Canister Vacuum ?

Assemble Swivel Assembly onto Kenmore Canister vac

\015 I have a Kenmore Progressive Vacuum Cleaner and need to replace the swivel assembly 3 prong. How do I replace that part? I need to remove the old one from the vacuum hose and can't figure out how to remove it and put the new one on. Thank You.\015

Answers :

Got this post off this web site...I just replaced my swivel and it worked:
\015\012To install a new swivel assembly, you will need 2 small, flat tip screw drivers. Unplug the vacuum. Push the screw drivers in between the hose and the collar where you see the seams in the plastic collar on the end where the hose enters the collar. This will release tabs that hold the collar to the swivel. Pry and pull the collar back over the hose and then pull the small screwdrivers out of the collar. Slide the collar back along the hose. Unplug the wiring connections from the hose. Pull the hose wires up and out of the holder on the swivel assembly. Lift the tabs on the side of the hose and pull it off of the swivel. Push the new swivel onto the hose. Align the hose wires and secure them in the holder. Plug the wires from the swivel into the hose wires (blue to blue, white to white). Secure the swivel wires into the wire holder on the swivel assembly. Push the collar back up the hose and onto the swivel with the plastic seams aligned with the tabs on each side of the hose. Snap the collar securely into place.
Repair Help & Product Troubleshooting for Kenmore 25512/ 25513 Progressive Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Assemble Swivel Assembly onto Kenmore Canister vac

Got this post off this web site...I just replaced my swivel and it worked:\015\012http://www.managemyhome.com/mmh/answers/Answers.action# ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@

Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

I have a Kenmore Canister Vac. I need to replace

Try forcing a flathead screwdriver between the flange (tab) on the hose collar and the tab on the swivel assembly itself, taking care not to gouge the wires. Saw one solution where they used 2 screwdrivers simultaneously; couldn't do that, but did lo ... Kenmore Vacuums

How do I disassemble the swivel assembly from the hose on a kenmore progressive canister vaccuum? thanks.

... Kenmore 22812 Bagged Canister Vacuum

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel

What is the exact model # please?Thanks!! ... Kenmore Vacuums

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.

Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

No power to head of Kenmore Progressive canister vac

... Vacuums

Kenmore progressive canister vac

... Kenmore 25512/ 25513 Progressive Canister Vacuum

No power to head of Kenmore Progressive canister vac

The extension wands are defective and have trouble with their plug connectors on each end. The power head has a reset button on top right but no lights mean no power which means the wand isn't connecting the power to anything. Sears has ... Kenmore 22812 Bagged Canister Vacuum

No power to head of Kenmore Progressive canister vac

... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Craftsman 8 gallon shop vac assembly diagram - Shop Vac 925-13 Canister Wet/Dry Vacuum

... Shop Vac 925-13 Canister Wet/Dry Vacuum

For the first time, I tried using my Kirby Sentria shampoo attachment. I've lost the manual but found instructions online for making the swap from regular vac to shampoo-er and got it all assembled. The foam laid down just fine, however, when I run the vac back over the foam to pick it up, there is not a stitch of water showing up in the tray. First I thought maybe it was bc I hadn't put that much of the foam/water onto the carpet, but 12 hours later, the carpet is still wet in spots. Clearly

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=638285\015\012Generic problem for all Vacuums\015\012For the first time, I\015\012Posted by MHicks on J ... Vacuums

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob

The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Power head for Kenmore Canister Vac

Another potential problem for the increase in difficulty in turning the beater bar (drum) could stem from extremely dirty bearings, located at each end of the beater bar. I've seen hair knotted up to the point it chokes the bar and significantly redu ... Kenmore Whispertone 29512 Vacuum

Owners manual for kenmore canister vac 11629219800

... Vacuums

Kenmore 25614/25615 Progressive bagged canister vac won't start

Sounds like there was a loose connection or loose wire that came in contact with another wire. check your cord for small burn holes, also could have shorted out in the hose or the wand. If you are comfortable to disassemble the vacuum i can walk you ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have a kenmore canister vacuum cleaner, 4 yrs. old, model #116.27815701. The powermate assembly, the one for the carpet, seems to have a short or something. The light goes on and off and the motor

... Kenmore Vacuums

Kenmore canister vac model 116. 2641381

Small sparks coming from the brushes is normal. That would be a thin line of sparking near the commutator/brush interaction point. Large or irregular sparks are different. The commutator (segmented copper item) should be fairly bright copper color ... Kenmore 22812 Bagged Canister Vacuum

I just got a Kenmore canister vac model 27514 and there is no suctionin the hose.

Is the bag full? if not it is clogged up ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

What belt do i need for a kenmore canister vac 116023513304

I'm not familiar with the model number that you posted. But if the picture you posted is the model you have then this is the belt you needhttp://vacbelts ... Kenmore 22812 Bagged Canister Vacuum

My vacuum is making a whistling sound and when I turn it off it momentarily gets louder and makes a honking sound. The vacuum is a Kenmore canister vac model # 116.27814. It has a new bag and filters.

... Kenmore 27814 Bagged Canister Vacuum

Have a kenmore canister vacuum cleaner which the power-mate parts don't work. I had loaned the vac out it came back with part of the hose smashed. I don't know if that is the problem.

The hose conducts power to the "power Mate" There are wires running end to end through the hose and handle. If your hose is grey with hard plastic cuffs at both ends, it is repairable, but you will need to locate the Smashed parts. If yo ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0678 seconds