Having problems with your Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum ?

Vacuum clogged. Can't figure out from where.

\015 Vacuum clogged. Can't figure out from where.\015

Answers :

Follow the air path: brush, handle, tube, bag, inlet filter, exhaust filter. Run the vacuum without these , in that order, to identify where the plug is. 
Repair Help & Product Troubleshooting for Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

U-Shaped piece I was in the hospital for a couple of nights and my 80 year old mother decided to go to my house and vacuum my house. When I went to get it out to vacuum the other night the u shaped part fell off. I guess my mom had somehow knocked it off. Now I cannot figure out where it goes. It is a plastic U-shaped piece. Can you help me? I sat for a hour trying to figure out where it goes.


It attaches at the bottom of the hose and goes into the bottom of the valve. Located on the back bottom of the unit. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Kenmore Handi-Mate Jr., Model # 116.36622501 generates a burning smell once i turn it on. It is out of warranty. There is any way i can look at the vacuum myself and figure out what is broken/burned and understand if it is worth fixing it? It vacuumed very nicely for about 2 years and it wasn't a cheap vacuum. Thank you very very much.


... Kenmore Vacuums

Kirby Sentria vacuum -- can't figure out how to hook up main hose to vacuum floors


First you need to press the foot pedal for the height adjustment all the way down to lift the front of the vacuum off the floor. On the front top of the vacuum where the LED lights are is a cover. That section will lift up by lifting just below the L ... Kirby Ultimate G Bagged Upright Vacuum

Have new oreck quest canister and having trouble figuring out how to change vacuum bag. I have the plastic piece that you attach bag to, but don't know where the piece fits into the vacuum. looking for a diagram or manual to see where to install the plastic piece


... Oreck Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My vacuum has suction with the long tube assembly but not any significant suction down by the rollers. I assume there is a clog or a problem between where the hose attaches to the machine and the rollers but I can't figure out where to look for it. HELP. I've only had this vacuum for a few months and I'm really dissapointed!


Go to the bottom of the machine and to the rhs of the rollers you can see the pipe - also remove hex panel on back and remove hose from elbow , i also found that a filter cx did wonders ... Miele S7210 Bagged Upright Vacuum

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

The retractable cord is stuck all the way out and will not go back in. Is there a simple way to fix this "disaster"??? without taking vacuum apart that is. And this is not my exact vacuum but I figure the cord problem would go for all of them. Ours is a ORANGE HEPA 360 Kenmore Whisper Belt 12 amp with PowerMate Model # 116.29219800


... Kenmore 27915 Bagged Canister Vacuum

This vacuum is not picking up anymore when used as an upright, however it does still work very well when using the hose and attachments, I have looked at the vacuum but I cannot figure out where the clog could be.


Is the brush rotating?Have you turned it over, taken off the bottom plate and cleaned it out?Is the belt in good shape or does it no longer rotate the brush? Is it on the proper floor/carpet setting for the surface you are cleaning? ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

A small thin antenna cord on my radio got sucked up, and I immediately turned my vacuum off and easily puled out the small cord, Afterward the brush on the vacuu would notrotate.. The belt is not broken on the vacuum is not broken. My husband cannot figure out what the problem is


Hi Susan. There may still be a piece of the cord in the brush roller bearing. Check the ends of the brush and have a look. If its clear the belt is probably strethed. An easy way to test this is to turn on machine a put you hand against brush, if it ... Riccar 8955 Upright Vacuum

Cleaning Filter Hi: I want to clean the filter on the B&D pet hepa vacuum, but can't figure out how to take it out of its housing. I can remove the housing from the actual vacuum, but don't know how to get the filter itself out. It sure does smell of dog, so any help would be appreciated.


... Black & Decker Black Decker Bagless Canister Pet VacVacuum

My husband vacuumed up a pound of feta cheese into the upright vacuum. Cheese is inside, on wheels, etc. I cannot figure out how to open so that I can clean the brush and the isides. Help! Linda


Yes - an independant vacuum repair shop is unlikely to repair (disassemble) - as this vac is no longer supported (in case something is broken during servicing).\015\012You will (probably) find the repair to be more than the cost of a new vac. ... Vacuums

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

Vacuum clogged. Can't figure out from where.


Follow the air path: brush, handle, tube, bag, inlet filter, exhaust filter. Run the vacuum without these , in that order, to identify where the plug is.  ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I can't figure out how to take apart my Panasonic MCE737 Vacuum cleaner to repair the retractable cable, can you help


... Vacuums

Belt broke I need to find out how to get in the vacuum to replace the belt but cannot figure it out. I do not have the owners manual for this Eurka The Boss Superlit bagless (402a) please e-mail me any directions if you know how to do it,thanks. [email protected]


How do i change the belt on my eureka the boss lite vacum ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

Need to remove bottom cover of Panasonic MCV7314 vacuum to see if the belt is broken. I can't figure out how to remove and can't find a manual online.


I did a search for the manual for that model and found a pdf file online that had instructions and pictures. It was still slightly different and hard to get off. I took out two screws and then held in two side "clips" and wrestled it off. I dont t ... Panasonic Vacuums

I have a new electrolux el7025a-r and it keeps cutting off while I am vacuuming. I am using the small powerhead on hard floors and I have checked the hoses for blockages and the bag is new. I can not figure out why it keeps turning off in the middle of a job.


The wands are notorious for going out on that unit. One or both probably need to be replaced. Try to get it done under warranty if you still have the receipt, but they shouldn't cost you too much if you can't. \015\012\015\01 ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Loosing suction I am loosing suction on my vacuum. I have only had it for about 6 months and cant figure out what is wrong. Can you help?


Well you did not state what model and brand this is, but usually if the hose or the dirt inlet by the brush roll gets clogged, then you lose suction. If you can't figure it out, usually there is a year warranty, take it in for warranty service. ... Vacuums

I need to replace the belt on my Sharp Vacuum Cleaner: Model ECTU4609. Can't find Owner's Manual and can't figure out how it goes on .


I have replaced vacumm belts before .. Normally it is located underneath..flip over the vacumm unscrew some screws.. open the cover..youll see a large roller pin type object remove it carefully noting how it is placed..pull it out.. and replace th ... Sharp Twin Energy EC-TU4606 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0599 seconds