Having problems with your Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum ?

Take apart to check motor

Answers :

Repair Help & Product Troubleshooting for Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together

... Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse

By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

E series How did you take your rainbow e series apart? Do you have a manual? I've got a few pieces off mine but can't see where any other screws are to completly take apart to be able to look at motor. Thanks Kelly

The clear lenses on either side of the top part of the E-series Rainbow are removable. If you look at the each lens you will see two sections on the top edge of each lens that looks like this |___| |___| about 1 1/2 inches in from each end. Put a ... Rainbow E series Canister Wet/Dry Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I want to take the vac apart to clean around the motor ?

I want to get the motor out from the vacuum. ... Rainbow E series Canister Wet/Dry Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.

That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

Looking for someone to instruct me on how to take apart my hoover steam vac so that I can check for clogging. It just stopped extracting water from the rug everything else sounds fine. The return holder is in place and has been checked many times. Any help?

First remove the dirty water tank then turn the unit on if your facing the front there is a duct on the right where the tank sets there should be a black seal around it if you have suction there then you will need to check the tank ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!


** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?

Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

I have an older Electrolux canister vacuum - model #2100 and the temperature sensor shuts down the motor. How to I take apart and clean?

Check to be certain the thermo lite is on and not the bag full indicator. The thermo detector is very reliable, but the bag fill valve often fails. If it is the thermo, check your hose and wand for blockage by dropping a coin through them,before ope ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Blowing out? I have checked all hoses for clogs, I have even taken it all apart, but it seems to be blowing out? The bag inside the canister is sucked in? Can the motor reverse on itself, I'm baffled!!

Did you check the inlet down by the brush roll? ... Bissell 3522 PowerForce Bagged Upright Vacuum

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?

You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I want to take apart a kone dirt devil and i know how it has to be done but i dont have 5 hands to do it. there has to be a tool that presses on the four sides of the case so you can slide the motor unit out. can you help me with this

... Dirt Devil KONE Cordless Hand Vacuum Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

My Roomba says to clean the brushes when the brushes are already clean. Is there something to take apart to check? I have already taken the brushes out. I don't know the model number, I think it's the 500 series, black and silver.

Turn the unit upside down and remove the bottom pan should be 4 or 5 screws depending on the model. next remove the 4 screws that hold the brush cartridge and pull the whole brush assembly out.using a can of compressed air cle ... Roomba 3005 Pro Robotic Vacuum

I have a windtunnel 2 vacuum. It sucked up a cord that wrapped around the beater bar. Now the bar won't turn. There was no smoke or sign of something burning. The motor still runs and there is suction but no turning. We have it apart but nothing is obvious. What should I check?

Check the actual beater bar for movement. I have seen the plastic melting, and bearings seized under such circumstances. Also I am unsure by your question, but the motor that creates the vacuum (sucking) is different than the motor that spins your ... Vacuums

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check

... Vacuums

No suction After taking the vacuum apart, I noticed there is no suction at all. The motor runs, belt runs, but no suction coming through.

You have a clog somewhere in the vacuum. Check the hose and the little trap door on the underneath side of sweeper.Does the brush turn? If not, then the belt that drives the brush is broken. Replace the beltJim ... Hoover Tempo Widepath Upright Vacuum - Blue

Motor is noisy like there is something stuck in it. I am looking for the service manual so I can see how to take it apart/

Hi\015\012Generally modern upright vacs don't have screws that you can undo to get into the motor and most Electrolux/Eureka models have sealed units. I suggest looking at the sole plate where the roller brush is, check for anything clogging the main ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

HORRID NOISE I have took it all apart and thoroughly cleaned it. It is still picking up dirt etc. But the noise sounds like its taking off. It is not that old so can not be the engine my mother has one that she has had much longer and is fine she has also checked it it is out of guarantee but is working the noise is terrible. Can you help???

Hitake out the belt and brush. Switch on. If the noise has gone you know its the brush. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have the Electrolux Intensity upright vacuum. The roller bar underneath that is used for carpet no longer turns. I have checked the belt that is attached to it. I'm afraid that it may be the motor. Where can I take it for service or shat do I do now? Kay

... Electrolux Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0605 seconds