Having problems with your Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum ?

How to replace the Terminal Cover on top of the Extension Wand

\015 I had a bad connection between the Wire Harness on the handle and the Terminal Cover on the Extension Wand. I replaced the wire harness, the the vacuum runs great. However, I bought the terminal cover because one of the contact pins looks "rusty" and I don't want to cause another poor connection. Will you please provide instructions for the removal of the Terminal Cover? I've played around with this enough to know that I may start to break something if I apply pressure in the wrong places.\015

Answers :

I saw this in another FixYa post

it tells midway down how to get access to the wand fuse (which has the two-prong terminals)
\015\012Comment posted on Feb 09, 20082bubbles\015\012ok here we go.. fine a small file that will fit the holes at the bottom\015\012of the wand and break the file so that the flat end fit into the wand.\015\012please make sure the wand is not plug in to anything. now put it into\015\012the hole and try to clean it out gently not too hard or you will damage\015\012the contacts. after that grab a needle nose pilers and very gently\015\012press the contacts. not a lot or it won't fit back into the power-mate.\015\012ok now for the top of the wand. if you look at the wand where the\015\012button is to extent the wand. on each side you will see a small clip.\015\012with a small flat head screw driver push into the clip at the point\015\012closer to the wand tube. it will pop out. make sure to check the clip\015\012to see how to put it back in. after both clips are out you will notice\015\012a that the clips left a gap. the back part of the wand or cover will\015\012now slip off. push it toward the gap. then up. after removing the\015\012cover. you will see a ribbon strip which is attached to the prongs or\015\012fuse .you can remove the fuse and then clean the contacts. please be\015\012careful. once this is done you then put it all together and try it out.\015\012the fuse is a part that you can buy at sears if you have to. let me\015\012know if this helps you out. if it seems like too much just take it to\015\012sears and ask them to replace the wand fuse for you instead of\015\012replacing the whole wand. hope this helps .
Repair Help & Product Troubleshooting for Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace the Terminal Cover on top of the Extension Wand


... Kenmore 22812 Bagged Canister Vacuum

How to replace the Terminal Cover on top of the Extension Wand


I saw this in another FixYa postit tells midway down how to get access to the wand fuse (which has the two-prong terminals)\015\012Comment posted on Feb 09, 20082bubbles\015\012ok here we go.. fine a small file that will fit the hol ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Replacing the extension wand terminal cover


Hi, It has been a while since I had to take one if these power heads apart. The Sears Service maual does little to explain the exact removal procedure of the cover. But from memory here goes. \015\012\015\012There are pressure locks on ... Kenmore Vacuums

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.


... Euro-Pro Vacuums

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

How to take apart wand of kenmore vacuum 116.24614400 to replace COVER #8191782 on Sears part


... Kenmore Vacuums

VAX UPRIGHT VACUUM CLEANER V91-P2/HOW TO REMOVE TOP COVER TO REPLACE DRIVE BELT.


... Vacuums

Brush not working on self-propelled wind tunnel U6471-900.I have replaced belt but can't get off top cover.


... Vacuums

Need replacement part, maroon cover top handle of Z570 cordless


Need replacement part, maroon cover top handle of Z570 cordless\015\012 \015\012Hello,\015\012I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedu ... Vacuums

Replacement head/tips I am looking for the heads/tips that go on the top of the wand.


Www.nubrilliance.com or you can call them to order new microdermabrasion tips and filters at 1-800-423-4248. You can also find them on EBay but I would suggest bidding oppo ... As Seen On TV Diamond Radiance

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

My vacuum makes a wierd sucking and blocking sound when turned on and when you put the extension tube on the suction decreases...but when just the wand handloe is on the suction is excellent...we replaced the barrel thinking it was broken but that hasnt fixed the problem


You did not list the make and model of your unit, so it is difficult to hunt for problems.\015\012\015\012Check to see if any of the tube vents might be open. They should be closed when in use.\015\012Also check to see there are no holes in th ... Vacuums

How do you get the smart mix dial to line back up when replacing the top plastic cover on a bissell pro heat pet.


First, insert the black plastic control valve all the way into the hole. Make sure that the rounded face with the cut in it is facing toward the tall part of the chamber/hole where you inserted the valve. Try to line up the dial with where the thre ... Bissell 8910 ProHeat Clear View Upright Vacuum

I am having trouble getting the wand extension to go all the way into the flexible tubing so that i can close off the top.


Is it a dyson? make sure the top handle is snapped in properly and that will release the clip and allow the wand to go in ... Vacuums

I have purchased a vaccum cleaner (Swift) from Nandilath G Mart, Kaimanam, Trivandrum on 08 Jan 2010 vide invoice No. TVM-27308 dated 08 Jan 2010. On the same day, inspection at my home , it is found that the extension tube piece packed in a plythene cover is cracked vertically, and cannot be used. Request instruct the concerned to replace the damaged part. Joy Babu.B, C-85, ISRO Staff Quarters, Pallithura-PO, Trivandrum-695586 Tele: 9495409241.


Contributors to this site offer advice only. We cannot act on your behalf. Suggest you contact your supplier direct. Good luck! ... Vacuums

Replacement wand for canister


Whne you had your first problem with it, the cord at the bottom probably should have replaced also, if one end gets scrotched, the other end does also. One big reason why this happens is connecting and dis-connecting the power head while power is st ... Vacuums

I am working on a u5290-900 hover vacuum ,when operating dust leaks out under dirt cup cover. i put a piece of card board on top of cover so extra presure would be applied to the top of cover. this seams to have stoped the leak , before adding the card board the cover seamed to lift at the back when cover was locked into place. what do you think?


Dear Sir:Will be better idea to replace the cup cover. The pice of card will not function for a long time. Proceed before another extra problem coming.God bless you ... Hoover U5290-900 Upright Vacuum

Eureka model 4335 - belt removal (top cover)


Hi.  There are 16 different models of Eureka 4335, and frankly I don't know how much difference there is between them.  You can download a copy of the user manual from the website below.\015\012\015\012If that doesn't work for you, pl ... Bissell Flip-It Select Hard Floor Cleaner - Volcanic Satin

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

Replace cover cover came off while replacing dust bag


... Miele Red Star Bagged Canister Vacuum

A 'burn' hole has appeared in the Microwave Outlet Cover causing arcing (or similar sparking and blue flashing!). Would replacing this cover with a new one solve the problem or does it suggest something that would quickly reoccur? Would it be an economical repair or should we ditch the machine for a replacement? Thanks in advance etc it is appreciated.


... Vacuums

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0440 seconds