Having problems with your Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum ?
Kenmoore Canister 25812 Failure
\015 The LED lights located on the extended hose do not light up when the cannister is operating and the entire agitator housing is dead...that is it does not work when the vacuum is turned on. Checked contacts...clean. Is there a circuit breaker for both?\015
Some of the powerheads have a circuit breaker on the top of it. Just push it to reset. May have a bad circuit pcb in the hose handle.
Repair Help & Product Troubleshooting for Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Kenmoore Canister 25812 Failure
Some of the powerheads have a circuit breaker on the top of it. Just push it to reset. May have a bad circuit pcb in the hose handle. ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum
No user manual/guidelines found in carton. Need some explanation of how best to use the canister, and clarification of the battery compartment 0 to 48 hours sliding switch functionality. Thank you.
You were supposed to be issued with all the pertinent manuals for the machine. Go back to the dealer and demand your manuals. ... Vacuums
My new Kenmoore Powermate 116 canister has poor suction. I have no pets and light dust. Its not picking up small particles on the wood floor with the floor attachment. When I put my hand to the suction it feels weak. Cleared hose and changed bag. Using again, same issues. This should not be happening with a new vacuum. Is it a bad design in the elbow joint of the hose? I want to return this!!!!
First of all disassemble the handle and hose as much as possible and examine the inside. Make sure there is not any significant debris lodged in the hose somewhere like a plastic bag or something.\015\012\015\012Also check at the top of t ... Kenmore 23912 Progressive PowerMate Bagged Canister Vacuum
I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope
Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums
I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.
You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I'm sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip
Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond ... Hayden Industries SuperVac 6000 Central System Vacuum
Hoover Uh30010com the hose on the canister does not stay lock (it keeps poping out). I heard great reviews on this vacuum but I am so dispointed with the canister I am ready to return it to the store, I think it is a waste of money if you can't use the canister... I cannot believe I did not find reviews on the canister.
You can take it back. they will return it they know this happens all the time. If you like canistar vacs you should get a tristar. they are the best! call me for more info 866-635-9254 John ... Hoover Vacuums
Need an on/off switch for a Hoover Windtunnel Canister S3639
MY WINDOW EXPLORER IS NOT OPEN ... Hoover S3755 WindTunnel Bagless Canister Vacuum
Webpage error detailsrn User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; FDM; AskTbPLTV52/22.214.171.12449) Timestamp: Wed, 1 Jun 2011 21:06:26 UTC Message: HTML Parsing Error: Unable to modify the parent container element before the child element is closed (KB927917) Line: 0 Char: 0 Code: 0 URI: http://www.facebook.com/hoshmend.ali1
... Euro-Pro PT205 Leaf Blower Powerful 12 AMP Leaf Blower, provides 205MPH air speed, Detachable Vaccum... Vacuum
I have a Dyson DC23 animal canister. This is the first time I emptied the canister. After putting it back on, the vacuum won't start. I have removed and reseated the canister several times, also attachments, but it will not start. Help!
... Dyson DC23ACTUSC Bagless Canister Cyclonic Vacuum
My kenmore progressive canister vacuum turns on only if the hose is attached to the floorwand. It seems that the canister motor is not working because I can't hear anything coming from the caniste
If the floor wand is powered, there may be an electrical connection that is broken when the wand is disconnected. This is part of the design, not necessarily a fault ... Vacuums
I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!
Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums
My wand on my canister began to spark and snap and smoke. The element was melting. and now I am stuck with only a working canister. the elememt or electrical hook up is burned up...and I guess I am gonna have to BUY ANOTHER wand or connection??? I don't know what to do... but this is a HUGE dissapointment. The canister still works... but no vacume head.
How's the hose?\015\012If it's only one wand, yes, you'll need to buy a new one. It depends on where it burnt out. If it was at a connection to the hose, the other wand, or the power nozzle, you need to check the connections thoroughly for di ... Electrolux Lux 5500 Canister Vacuum
My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa
... Electrolux Vacuums
Kenmore progressive canister bad connection from hose to canister
It could be, the female part of the connector is stretched open. You can usually insert something, like a dart, between the sleeve and the holder, to tighten it. If you paid with Pay Pal, see about getting your money back. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
25512/ 25513 Progressive Canister Vacuum: HI, we have a kenmore progressive canister vacuum ...
Cord bad at male prongs, or fuse near motor blown. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
Dust collects on outside of canister on Hoover twin chamber bagless cleaner . I have replaced the filter & rubber gasket at bottom of the canister ,checked for blockage.
... Hoover Vacuums
Canister 1 canister not working
The filters are not clean on both sides. Check the main filter at the top and the internal filters for each side, clear and brush cleanly and gently to remove all clogged dirt as well as checking the hose and inspection airways i.e. when the bin is t ... Dirt Devil Reaction Twin Cyclone Upright Vacuum
I am unable to open the canister to remove the old bag, unclipping the 2 clips on the side does not release the canister. What am I doing wrong?
Overtime the dirt canister can get somewhat stuck. Once you unclip it, you will need to apply some force and pull down. The dirt canister should release. ... Broan-NuTone CV350 Central Vacuum
I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!
Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum
I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger
There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums
I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.
... Kenmore EVO All Surface Floor Cleaner Vacuum
Where is fuse kenmore canister vacuum - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?
Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum
Overheated vacuum After I finished vacuuming the library last night I changed the bag and shook out both filters and vacuum would not restart. The canister unit felt real warm to the touch but I had been using it a least 1/2 hour non stop. The bag was pretty full but not overly so. It's a Simplicity canister with power head. The carpet is long shag from the 70's Did it just over heat? Thanks Shauna
It normally won't over heat unless the bag is too full, the filters are clogged, or you have have a clog in the hose or down by the brush roll, the inlet may be clogged. Some will restart after a while, some others have a reset to push. If it won't ... Simplicity 7850 Premier Bagged Canister Vacuum