Having problems with your Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum ?

Hi there, I have a progressive upright vaccuum and the brushes are not spinning. Any suggestions?

Answers :

Push in the red reset button. It's on the bottom side where the rollerbrush is.
Repair Help & Product Troubleshooting for Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi there, I have a progressive upright vaccuum and the brushes are not spinning. Any suggestions?

Push in the red reset button. It's on the bottom side where the rollerbrush is. ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I have a VAX bagless upright for pet har. The brush has stopped spinning, but there is suction as the hand held attachments work. Any suggestions?

The belt is broken --- replace with a new belt.\015\012\015\012c... ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

My Dyson DC14 all surface vaccuum does not have suction except when it is upright. The brush is spinning but very little to no suction.

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

The brush stopped spinning on my Dyson upright

Hi there'\015\012 common possible defective is that motor is not functioning,several factors can be check if you have a knowledge on electrical and motor\015\012circuit you can easily diagnose your problem on your vacuum.\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a kenmore beltless upright the beater brush dosetn spin

If it is direct drive then the motor or the wireing to the motor are bad. If it is gear driven then the gears are probally stripped. ... Windsor SR12 Sensor Bagged Upright Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?

Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

The flexible brush on my unit does not spin. It did 'by accident' pick up a cat poo that didnt make the litter tray while I was out, (and it happily spread it all over the house and skirting boards). I cleaned the unit, removed the base and wiped everything clean. I've unscrewed the flexible brush and cleaned underneath it but it still wont spin. Any suggestions?

... iRobot Roomba 530 Robotic Vacuum

My vacuum's cyclonic action is not spinning and creating very little vacuum pressure through hose or floor brush area. I already checked, brushes are spinning, there is no apparent blockage in the canister, I took it completely apart and removed excess dust from the filter. Still no good vacuum. Any suggestions?

The following filter in your in your dump cup needs to be replaced. \015\012F24 Dirt Devil "I" Bagless Upright Vacuum Replacement Filter Style F24 ... Dirt Devil M130005 Bagless Upright Cyclonic Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?

Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My vaccuum has lost suction. I changed the bag and cleaned everything out. The vaccuum is only 6 years old. I even replaced the belt around the brush. When I turn the vaccuum on it smells like burning rubber. My vaccuum is an upright 12 amp model #33000300C serial #Y347012385

... Kenmore Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom

... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.

You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

We are trying to replace the belt on the bissell 89q9 model. We purchased belt 8 and got in onto the brush however the brush doesn't spin anymore. Even trying to turn it by hand doesn't work. One end of the brush has a round end to slide in (clear end piece); however the other has a rectangular end to slide in (black end) so we don't even know how it ever turned. Any suggestions?

Remove the beater brush assy & remove the\015\012shaft & brgs that go through it 7 clean out the \015\012hair,fuss ect,so it will turn\015\012\015\012You need to take your vacuum apart once a year or more\015\012to clean ... Vacuums

Stuck brush roller on Kenmore progressive upright

... Kenmore 22085 Bagged Canister Vacuum

Spin brushes will not spin - Hoover F7458-900 Upright Vacuum

... Hoover F7458-900 Upright Vacuum

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman

\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem

... Oreck XL2200 Bagged Upright Vacuum

Brush doesn't spin. no suction felt at brush - Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Check that the brush has not become fouled with string, etc. If it still doesn't work try the following.\015\012\015\012Some Dyson's have a switch for the brush on the front of the handle. If yours does, please make sure its on. This m ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The spin scrub brushes do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Try this: Make sure the setting is set to floor, then remove the little window (you might need a flat screwdriver to "pry" it up) and clean off the filter. If there is a blockage, the brushes will not spin! I hope this helps, if so, please give fe ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1597 seconds