Having problems with your Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum ?

Have Kenmore Progressive Direct Drive upright. Roller not spinning. Have cleaned all debree with no luck. Took apart and discovered white plug disconnected from motor. No visible place to reinsert. Need assistance or skamatic


Answers :

Repair Help & Product Troubleshooting for Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have Kenmore Progressive Direct Drive upright. Roller not spinning. Have cleaned all debree with no luck. Took apart and discovered white plug disconnected from motor. No visible place to reinsert. Need assistance or skamatic


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?


... Oreck XL Ultra Bagged Upright Vacuum

Need to change the motor on dc07 how do you get the motor out I have loosened and taken out all the screws and still cant disconnect the power cable in


Have you looked at www.dysonmedic.com ?\015\012\015\012It has a really good feature on changing a DC07 motor. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???


Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

I have a Genie home wet/dry shop vacuum model 300PCA, 7.5 amp,rn1.1 HP. Electirc motor bearings are worn and in need of replacement motor. Unable to locate any Genie web sites Any assistance will be deeply appreciated, Thanks. [email protected]


... Vacuums

Stopped working hello im in france, so my henry has a two pin plug. i feel all that needs changing is a fuse, but i carnt find it. i have taken out every possible screw searching for it but to no luck. iv checked and cleaned wireing and checked cable for nicks. im now begining to think maybe the motor has gone?


Hi!  Sorry you've had to wait so long for a reply, but I've only just stumbled upon your problem.  You probably don't need help any longer, but here goes anyway!\015\012You will not find a fuse, because there isn't one.  If your Henry ... Numatic Henry Bagged Canister Vacuum

92L3-W this unit was fine when new, did a good job, after a few months it got very loud. it is so loud you need ear plugs to use it. i have checked and cleaned it. there is'nt any visible problem with it. after cleaning and changing all filters it still is very loud a lot more than when it was new.


... Bissell Vacuums

I have a White Model 258SM sewing machine and when I have all the settings set for straight stitching, the needle bar still moves side to side. Is there something that I am doing wrong or is this normal and I just don't remember it happening before? Thank you for your assistance. If repair is needed, can you recommend someone in the Brainerd, MN area?


... Vacuums

I have a Euro-Pro Shark Cordless Sweeper Model UV610. The motor still runs but the spinning brushes are no longer spinning. Can someone that is familiar with this appliance please assist me at repairing it and/or what parts I may need for repairing it? Thanks T.R.


IT SOUNDS LIKE YOU HAVE A BROKEN BELT, THAT CONNECTS THE MOTOR TO THE ROTOR BRUSH. ... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

I used my steamer one afternoon, and the next morning, when I plugged it in and tried to use it, it would not produce steam. What can I do? I love to clean the grout etween the floor tile with it. I need to finish my job as soon as possible. Thank you for your assistance.


Hi,Sounds like the switch on the handle or the steam release solenoid on the steam chamber is faulty ,use a volt meter/tester to see if you have current to the solenoid when you turn on the switch. \015\012If there is no current you have to go ... Euro-Pro S3325 Handheld Steam Vacuum

Oreck schematic Did you get the schematic you requested? I need same. I blew the lights because plugged in wrong spot. Motor has 2 opposite terminals with black dots and 2 without.


... Oreck XL21 Bagged Upright Vacuum

My Kenmore canaster vacuum Mod# 116.25513506 runs continously when plugged in regardless of the on/off hand controlled switch.. Disconnecting the switch located on the hose assembly has no affect of the continous vacuum operation. What component in the electric motor circuit is at fault and what would be the cost of repair?


... Kenmore Vacuums

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt


... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

I need the wiring diagram for the motor.


... Hoover Commercial Windtunnel C1705-900 Bagged Upright Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

Shop vac has something plugging hose, I can't disconnect hose


The hose just pushes in. You should be able to just twist the hose and pull it out. After you get it out, try attaching it to the discharge side and try to blow the obstruction out. If that doesn't work, try running a fishing pole or something inside ... Shop Vac (464-38-10) Canister Wet/Dry Vacuum

Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.


You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums

I need a manual on a trim a home christmas tree set its a aspen pine with 600 lights it has a series of steps on how to plug in the numerous plugs on it so that all the lights light up...lost manual need help


... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

I need to replace the motor on a Sebo Automatic X!


OK, here goes...  NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine.\015\012\015\012STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compar ... Sebo Automatic X1 Bagged Upright Vacuum

Have a 2yr old Broan VX6000C built in vacuum. Has power when plugged in I have disconnected unit from the wall and the wires to the outlets are also disconnected and the power unit still runs as soon as it is plugged in???


... Broan-NuTone Vacuums

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0943 seconds