Having problems with your Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum ?

The brush has stopped turning when used in the upright position

Answers :

Mine also stopped turning. I tried pushing the red reset button on the left side of the vacuum, down by the agitator on/off switch. It didnt work at first, and I then realized it was stuck. I used a pair of tweezers to pull it out and the agitator is working great now! Good luck. Hope this might help you.
I have one too and I'm trying to fix it as I write this.I also have an older version and I've had no luck.I've taken evey screw out ,spayed tweeked and tried everything possible.my solution would be to stay away from Hoover steam spin scrubs.I'm going to invest in one with brushes like a vacuum.Those that are easily replaced as well as the drive for it be it a belt or a turbine like I've read this unit has
Repair Help & Product Troubleshooting for Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell 9400's brush rollers do not stop turning. When I was using the hose attachment for the stairs the handle was in the upright position and the brushes kept turning. Also water was leaking out of the rear right side onto the the carpet under the machine.

... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

The brush has stopped turning when used in the upright position

Mine also stopped turning. I tried pushing the red reset button on the left side of the vacuum, down by the agitator on/off switch. It didnt work at first, and I then realized it was stuck. I used a pair of tweezers to pull it out and the agitator ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Eureka 4870 brush won't stop turning in upright position

There will be a linkage that as come loose and not operating the limit switch to turn it off, try looking at 23. Idler Clamp Assembly on the link below. ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]

Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Sebo upright barged hoover- good suction using hose, brush wont turn, sounds fine when running, nasty wineing noise when stopping?? help!! i love my hoover, have checked for bolckages....

The real clue seems to be the brush is not turning, a bad belt is possible or a blockage at that head, if you cannot get the brush moving the rest does not matter. ... Sebo Felix Classic Bagged Upright Vacuum

Brush roller does not turn off in upright position

Make sure there is not a lever to move in order to stop the brushes/agitator...\015\012if the belt makes contact with the end of the shaft the brushes will rotate...\015\012tighten all of course/and take the panel of to check behind the b ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My sd40025 dirt devil ..it is not a upright. it is the follow along, bagless vacuum. has wonderful pick-up but the brush stopped spinning when i was vacumming my rug..i love this vacumm but it is only the third time i have used it. It is brand new. Why would the brush stop after maybe 20 minutes of total use?..please advise

... Dirt Devil SD40020 Bagged Canister Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?

I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

4870 Boss Smartvac. The vacuum tipped over and now the brush control lever will not stay in the carpet position. I can't get the brush to turn unless I push down and hold the lever. As soon as I let up on the lever the brush stops turning. Any ideas. The vacuum is only a month old.

The Boss has a slide lever on the top of the power nozzle with two position choices. One position is "Carpet" and the other is "hard/bare Floor". The power nozzle brush roll is activated when the lever is in the Carpet position, and it is t ... Eureka Smartvac 4870 Bagged Upright Vacuum

The brush on my Electrolux Ambassador III vacum stops turning after vacuming for only a few minutes every time I use it. The power nozzel is less than a year old and except for the brush not wanting to turn, it operates just fine. Any suggestions on how to fix the problem?

... Electrolux Vacuums

I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?

Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,

... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?

Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brush roller on Hoover upright stops turning

There should be a belt tensioner for the V belt, maybe it is not contacting the belt when you tilt the handle back. If this is less then 1 year old, then it is under warranty, take it in to a warranty servicer for warranty repair. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

While using the vacuum, the brushes stopped turning.

Check the drum. Hair will rap around the axxel and stop the brush from turning. Cut this hair with a razor and place a small drop of oil on the end of the axel. ... Kenmore 23313 Whispertone Bagged Canister Vacuum

It stopped sucking @ brush stopped turning - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Usually on this vacuum those two problems are not related, but if you got a lot of stuff stuck in the brushroll and in the suction tube at the same time it could happen. Check the belt to make sure it's not broken. If the vacuum is over a year old th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Model DC-31 Animal. Brand new out of the box. Brush turns intermittently at initial start-up then stops completely after 30 sec. to 1 minute of using. Belt is in-tact and functioning. Belt motor hand-turns with some resistance felt.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a DC07 and the brush has stopped turning. What do I ed to check? I had just cleaned the whole brush of hair and maybe I put it b back n the wrong position.

It has a reset button on the right side \012\012\012if that does not work for you call dyson they will help you out ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.

I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I purchased a hoover windtunnel 2 model#u8361900 in Dec 2007.I am very disappointed because the self cleaning filter is not turning and particles keep clogging in that area. I have manually removed the particles but the filter will not turn.I also haven't been able to use the pet brush for some time.The cleaner has not been used hard about once a week since it was purchased.I am not happy that this product has stopped working effiently since purchased 6 months ago. Thank you Marcia Long Pottstow

The filter stands up right.the bottom goes in first then snap in the top.turn it by hand and you should hear it click if you have it in right ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.4985 seconds