Having problems with your Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum ?

Hair around wheels

\015 My daughter has very long hair and no matter what vacume we buy, her hair always wraps aroung the beater bar and wheels and if not cut off or cleared will cause the belt to break. Is there a vacume able to pick up hair and not get entangled?\015

Answers :

No. I have 3 women and 2 dogs under my roof and have the same problem. My wife uses a Eureka vacuum that cost $140.00 and it seems to handle this better than our old Kerby.

We take a broom and swiffer and collect what hair we can from the bathroom areas, etc, before sweeping to avoid this problem.
Repair Help & Product Troubleshooting for Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hair around wheels

No. I have 3 women and 2 dogs under my roof and have the same problem. My wife uses a Eureka vacuum that cost $140.00 and it seems to handle this better than our old Kerby. We take a broom and swiffer and collect what hair we can from t ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?

You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum

My new pet hair roomba works great except it leaves lines of pet hair along edges of furniture and circles of pet hair around table legs

... iRobot Roomba 560 Robotic Vacuum

Dc17 -too much pet hair around the belt gears

I was having the same trouble and it was driving me nuts.  I tried cleaning and it did not work.  Then I tore the brush assembly off and looked up into where the little tooth gear is.  I saw something that did not look right.  The ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Bin barely fills. Lots of dog hair between brushes and bin, and is now dropping hair balls as it goes around the house

This is why Roomba recommends a thorough clean of your carpet with a standard vac prior to using your mini vac. Once all heavy debris has been removed, the roomba will maintain that state of clean. If you have that much dog hair, you cant expect such ... iRobot 560 Roomba Vacuuming Robot, Black and Silver Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water.......and how do i remove the wheel on my bissell

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Hair stuck in wheel

... Oreck XL Ultra Bagged Upright Vacuum

Dc17 -too much pet hair around the belt gears

Go to a DC14 there is a reason why Dyson calls it the Animal. It's ment for all the pet hair and things like that, listen to what Dyson recommends you, they know their products well. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hair around belt area

Design flaw. You have to clean that out regularly :) ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brush wheel will not go around?

Make sure the carpet/floor selector switch is in the carpet position. if that is good then you probably have a broken belt. Unfortunately a complete clutch assembly will have to be installed. Just the belts cannot be changed ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No power I ran over an elastic hair band with the hose that wrapped around the shaft (not the brush). Since then, no power. could the motor have burned up?

If pieces wrapped around the fan fins and jammed the fan from turning, this could be the problem. You may have to remove the front of the vac to get to the fan. ... Kirby G5 Bagged Upright Vacuum

The brushes are not going around and, of course, not picking up hair, fuzz, etc.

Check the belt that turns the brush, it sometimes gets worn and looses friction, causing loss of spin. ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

I have a 4.5 HP Craftman Wet Dry vacuum. The canister craked around where the wheels are. I probably need a new canister. Would you know where I can pick one up?

I use searspartsdirect.com. this site has parts breakdowns too. You will just need to check the price. sometimes they charge too much for parts and its not worth it. this is a true Sears website.If this helps, please rate this answer. ... Craftsman 17765 Canister Wet/Dry Vacuum

My dyson dc 07 brush will not rotate. I have cleaned all hair and debris from around the brush and no change. I can not even figure out how to look and see if the belt is still attached. Suggestions?

DC07s are not easy to check the belt on, in fact depending on which exact model you have there are probably two belts.\015\012One connects the output of the motor to the clutch mechanism (one end of which has the control knob that ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Agitator unit on Kenmore Progressive 116.25915503 won't spin. I have cleaned out all hair and string wrapped around it. Belt is good. It seems to spin on one side but stuck on the other. Could string be caught somewhere?

Pry the end caps off the brush bar, you will find hair and string wrapped up tight in the end. the bearing may also be shot, you can try and oil it up a bit to keep it spinning.\012\012<!-- from fixya rte --> ... Kenmore Vacuums

I have a Bissell proheat 2x and it leaks water around the wheel area and drains the solution tank quickly.

Check to see if the seal came off the tank and stuck in the dock ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How to refit the front brush belt driven roller ? We removed the roller accidentaly when cleaning out hair that had got wrapped around the roller. How can we put it back in?

Hi well if you go onto youtube and look for replace dyson clutch it will show you how to refit your brush good luck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My roomba pro elite just goes around in a circle. how can I fix this? I have cleaned the roomba as thoroughly as I can. Could it be a recently changed wheel tread?

The infrared sensor circuit has failed, u will need to have it repaired ... Roomba Pro Elite Bagless Robotic Vacuum

I took the vacuum apart, and cleaned the filter, cannister reservoir, removed all the hair which was wrapped around the beater bar. One the filter was dry (next day), I put it all back together. Now, there is no suction, and it sounds differently than it did before.

Check its assembled correctly . Sounds like something is out.... ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0239 seconds