Having problems with your Kenmore 33728 LP2 Low Profile Upright Vacuum ?

Need a belt replacement - Kenmore 33728 LP2 Low Profile Upright Vacuum


Answers :

Repair Help & Product Troubleshooting for Kenmore 33728 LP2 Low Profile Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need a belt replacement - Kenmore 33728 LP2 Low Profile Upright Vacuum


... Kenmore 33728 LP2 Low Profile Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Where can I buy lost attachments? - Kenmore 33729 LP2 Low Profile Upright Vacuum


Take this link to Sears website and enter your entire model number aka. 000.000000 three digits, decimal, followed buy the remainder of the model number.\015\012\015\012 ... Kenmore 33729 LP2 Low Profile Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

We have a Kenmore Grab-N-Go Upright Vacuum with a Hepa filter. We lost the yellow filter canister that goes in the top of the vacuum and need to replace it and the filter that goes in it. Is there somewhere we can purchase a replacement part?


... Kenmore 34722 Grab-N-Go Upright Vacuum

I need to replace a belt on the shark infinity pet care system upright vacuum. I have the belt I need a manual to show me how to put it on


... Euro-Pro NV31 Infinity Vacuum

Replacing belt in Kenmore Grab-N-Go vacuum - Kenmore 34722 Grab-N-Go Upright Vacuum


... Kenmore 34722 Grab-N-Go Upright Vacuum

Need to replace belt on 4773 eureka vacuum - Eureka 12 Amp Capture Vacuum Upright Vacuum


... Eureka 12 Amp Capture Vacuum Upright Vacuum

I need to replace the agitator belt on a Hoover Elite U4465-9 upright vacuum cleaner. I have removed the bottom cover, but there is no access to the motor spindle to loop the belt around. How do I do this?


... Vacuums

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?


Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need tp replace belt on Kenmore CB-3 - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Need to replace belt on a Kenmore Model: 116 37312690 vacuum. Have taken torn belt off. Is there a diagram available? I have lost owner's manual.


Instructions:\015\012\015\012\015\012 ... Vacuums

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t


... Vacuums

Belt broke on my Dyson Animal DC17 & I need to replace it. How do you replace it & can you get them at Lowe's where we purchased the vacuum?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Lost manual on vacum need to replace belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Remove the bottom cover of the sweeper head, then remove the brush roller along with the belt if still there. Clean the brush end-bearings--the roller ends and the interior of the bushings. Then oil the bearings lightly with 3-1 oil or similar. Place ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Kenmore Progressive upright vacuum - how to replace the belt


... Kenmore 33721 Upright Vacuum

Need to replace belt in Kenmore Vacuum Power-mate nozzle


Hello,\015\012\015\012Here's what you'll need to replace a belt on a Kenmore canister vacuum:\015\012\015\012- Phillips Head Screw Driver\015\012- Flat Head Screw Driver\015\012\015\012There are two different ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Need to replace belt on my Kenmore Progressive Vacuum Model # 116


HiOn your products manual is the replacement procedure.www.managemylife.com/mmh/lis_pdf/OWNM/L0311026.pdf ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I need to replace the belt. how do i do it - Kenmore 22812 Bagged Canister Vacuum


Buy a manuel ... Kenmore 22812 Bagged Canister Vacuum

I need help replacing my belt - Bissell 6594 PowerForce Bagless Upright Vacuum


Just changed mine. I have a Turbo Force 6585. Flip it over and press with your fingers on clip #s 2,3 and 4 (This releases the cover over the roller brush - The clip locations are labeled on the plastic cover). Remove the cover - this will expose the ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

I need topknow how to replace the belt - Kirby G4 Bagged Upright Vacuum


The following link lead to the Kirby site, which has an excellent instruction video for replacing the belt. Just click on one of the symbols to the right of "Changing the Belt". If you don't have either of these video viewers, you can download one at ... Kirby G4 Bagged Upright Vacuum

I need to replace my belt on my kirby g4 - Kirby G4 Bagged Upright Vacuum


Hello, amhillI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ... Kirby G4 Bagged Upright Vacuum

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

The belt needs replacing - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


Here is the manual to your Hoover U6630www.thinkvacuums.com/pdf/uprights/Hoover_U6630.pdfit goes into detail on how to change the belt and which belt to purchase. Ask for a flat belt Hoover part No. 38528035 when you're going to pur ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1495 seconds