Having problems with your Kenmore 34612 Bagged Upright Vacuum ?

Replace the belt on a upright vac

\015 I know the belt goes around the roller on the upright vacuum, but does the belt attach to a roller inside?\015

Answers :

There is a very small wheel attached to the motors drive. Belt goes around the motor drive wheel and then around the drive roller assembly
Repair Help & Product Troubleshooting for Kenmore 34612 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.


If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

I need to replace the belt on my hoover fusion plus upright vac. But I cannot find what belt it takes. the number on the belt is worn off


Hello : \015\012\015\0121:Unplug your Hoover vacuum. Turn the vacuum up-side-down and place the motor and vacuum portion on a counter top with the handle hanging down toward the floor. This makes it easy to work on the underside of ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

Replace the belt on a upright vac


There is a very small wheel attached to the motors drive. Belt goes around the motor drive wheel and then around the drive roller assembly ... Kenmore 34612 Bagged Upright Vacuum

How do I replace belt on Eureka smart vac? - Eureka Smartvac 4870 Bagged Upright Vacuum


... Eureka Smartvac 4870 Bagged Upright Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

Looking to replace vac belt on eureka altima bagless upright


Hi Jim\015\012You should find the cross head screws on top of the hood - look below the duster and there should be a screw there, also another screw on the other side and two either side of the main floor head.  ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt


On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike


... Hoover Vacuums

Vac wasn't propelling. Replaced the flat belt, vac now runs OK, but the belt is half off the pulley. Question, is there any alignment adjustment to center the belt on the pulley? Thanks, ****


Hummm, ususally alignment is not adjustable, unless something is loose or really worn. ... Blair Hoover WindTunnel Bagged Upright Vacuum at com

How do I repalce the belt on Dirt Devil Swivel Glide upright vac?


Four screws hold the bottom plate in place. Turn the vac upside down and remove the screws that hold the cover(bottom plate) over the brush roll in place. Remove the plate and you are there. ... Dirt Devil M088910 Swivel Glide Vision Bagless Upright Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.


I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1


As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Have the empower upright cleaner. belt broke. can not find part #36528-040belt. can find a lot of hoover belts but not this #.Is there another hoover belt that will work on this vac?


No. if the wrong belt you will have problems. This is a common belt for Hoover, it used to be 36528027, but the number changed to the 36528040, also 40201190 is the newest number for this belt. Most repair vacuum repair shops should have this belt. ... Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

I need to replace the belt on my eureka canister vac. have the belt and screwdriver, now what? how to get the housing off? etc.


Can you please specify the type of model that you have? The model that you listed this repair question under, the S3686 doesn't even have a belt on the vacuum cleaner. The model number can be found on the bottom of the vacuum on a sticker that als ... Eureka Sanitaire S3686 Bagged Canister Vacuum

Replace belt for dyson upright - Dyson DC07 Bagless Upright Cyclonic Vacuum


DC07s have two belts - one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.I suspect the belt ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0778 seconds