Having problems with your Kenmore 34722 Grab-N-Go Upright Vacuum ?

Replacing belt in Kenmore Grab-N-Go vacuum - Kenmore 34722 Grab-N-Go Upright Vacuum


Answers :

Repair Help & Product Troubleshooting for Kenmore 34722 Grab-N-Go Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing belt in Kenmore Grab-N-Go vacuum - Kenmore 34722 Grab-N-Go Upright Vacuum


... Kenmore 34722 Grab-N-Go Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

We have a Kenmore Grab-N-Go Upright Vacuum with a Hepa filter. We lost the yellow filter canister that goes in the top of the vacuum and need to replace it and the filter that goes in it. Is there somewhere we can purchase a replacement part?


... Kenmore 34722 Grab-N-Go Upright Vacuum

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t


... Vacuums

Kenmore Progressive upright vacuum - how to replace the belt


... Kenmore 33721 Upright Vacuum

How to replalce the belt - Kenmore 34723 Grab-N-Go Upright Vacuum


Your instruction book shows you how to change this belt it should be easy just check the top and see if you lock tabs to remove the cover ... Kenmore 34723 Grab-N-Go Upright Vacuum

I have a kenmore upright vacuum model #116.35922500. The agitator tube doesn't turn. It doesn't have a belt for the agitator. It has an overload protector. I reset it, but it keeps poping back up. Should I replace the overload protector?


The reset is for your safety no belt ,probly a direct drive motor issues ,maybe the brushes it is detecting a short and pops the reset. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

How to change a belt??? - Kenmore 34723 Grab-N-Go Upright Vacuum


... Kenmore 34723 Grab-N-Go Upright Vacuum

Need a belt replacement - Kenmore 33728 LP2 Low Profile Upright Vacuum


... Kenmore 33728 LP2 Low Profile Upright Vacuum

Kenmore Stylite Retrax Upright Vacuum Belt broke


... Vacuums

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike


... Hoover Vacuums

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

Kenmore canister vacuum how to replace belt - Kenmore 22313 Bagged Canister Vacuum


... Kenmore 22313 Bagged Canister Vacuum

Lever & belt placement in Kenmore Progressive upright vacuum


You are correct. The belt is supposed to go around the peg that is connected to the lever so that when it is on the Floor /Tools setting the belt is not driven by the drive shaft. ... Kenmore Vacuums

How do i change my Kenmore upright vacuum belt?


... Kenmore 33721 Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

Need to replace belt on 4773 eureka vacuum - Eureka 12 Amp Capture Vacuum Upright Vacuum


... Eureka 12 Amp Capture Vacuum Upright Vacuum

Belt replacement in Hoover Sprint upright vacuum


Take the screws off the bottom. Use a flat head press down snap the bottom over off. The housing on top you gotta snap off. ... Vacuums

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?


This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

How to replace Hoover Windtunnel Upright Vacuum fan belt? What does the belt attach to?


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?


Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

On an old upright prolux plus, I just replaced the belt and cleaned out the brush motor, ran the vacuum for a bit, then the vacuum motor died...it's always run great. any suggestions of what to check?


... Electrolux Vacuums

How do i replace the belt on my vacuum - Fantom Vacums Cyclone XT Upright Vacuum


There are two black screws on the back of the hood top that need to be taken out and then the top hood will come off forward. Then you can see the belt and rollerbrush. Slide to rollerbrush out and put on a new belt to the motor pulley and then put ... Fantom Vacums Cyclone XT Upright Vacuum

My question earlier today referred to a Kenmore Progressive upright vacuum. Your answer suggested that I change a belt, if the reset button did not work. Does a direct drive really have a belt? Regards, Jim Buckley


Direct drive does not have a belt. It is a shaft with gears. What is wrong with your vaccum? Maby i can help. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1048 seconds