Having problems with your Kenmore 35622 Upright Vacuum ?

The power belt keeps comming off

\015 Kenmore upright whispertone model 38199990\015

Answers :

Repair Help & Product Troubleshooting for Kenmore 35622 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power belt keeps comming off

... Kenmore 35622 Upright Vacuum

I have a eureka power paw that keeps breaking belts. there doesnt seem to be a part that keeps the belt in place

My belt keeps breaking too, but worse is that I can't find out the size for replacing. Who knows the size I need for the Eureka Power Paw? ... Eureka Vacuums

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?

I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

How can determine when it's time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I'm cleaning? Thanks, Jim

Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck! ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Filter queen power head belt keeps falling off.

... Filter Queen Majestic Canister Vacuum

Vacumm Belt keeps coming off.

Stick a little bit of tape on the inner half of the spindle, this will put an angle on the belt and should prevent it slipping off. ... Hoover Vacuums

Belt keeps sliding over on the roller bar and rubbing on plastic parts. Belt is a "U" belt and I am told it should be a "R" belt. Sears sold me a "U" so I will try and find the R tomorrow. What keeps the belt other than tension from sliding onn the roller bar? Could it be that just the wrong belt could cause this??

The 4870 Series uses Part number 61110. It is a "R" Belt. It will appear too be to large. This is normal. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Keep replacing belt that drives brusher but keeps breaking. When feel belt driver rod it is superheated.....could it be melting into the stretched belt causing it to weaken?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=559226\015\012Generic problem for all Vacuums\015\012Keep replacing belt that drives\015\012 ... Vacuums

I keep replacing the belt and keeps melting and breaks. what do i need to do? everything else is working, the little piece of metal that hooks on the belt gets too hot and melt the belt

I think your talking about the motor spindel,,(the little metal bit?) if the motor is that hot its going to burn out soon, check that the brush is free to turn if its tight free it off its full of grit or fluff also check that the motor turns freely ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.

On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

How do you change a belt for the belt on the Royal Part #2-470010-801, Power carpet head attachment for the Royal Classic Power Team canister model #4750?

... Royal Vacuums

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!

... Vacuums

Power Head keeps cutting in and out while vacuuming???Canister motor keeps running but the power head starts and stops like there is a short or some loss of connection somewhere. Any ideas?

My kenmore progressive vacuum had the same problem. The electrical terminal at the bottom of the wand was corroded. I used a flat head screw driver to scrape the female portion of the connector as best as I could. I then took off the plastic cover on ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina

Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa

Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.

I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Replaced the belts on Saturday with belts that were purchased in 2003 but never needed. It is Monday and the small belt has already cracked and separated from the center fiberglass or whatever the band is made of. Is there any way to keep these belts from drying out in Alaska?

Hi Alaska,You can put a small amount of vaseline or a tiny bit of any oil on the back and ONLY the back of the belt Do not get any on the sides or inside of belt. Please be sparing with the oil.You can also put these in a zip lock b ... Vacuums

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.

I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The belt keeps coming off. There is a little U shaped metal piece that came off when the belt first came off. Where does it go? When we first got the vacuum, we sucked something up and the belt came off and that little metal piece fell out. The belt now periodically comes off when we bump something. Please help us!!!!!!!!!!!!

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0615 seconds