Having problems with your Kenmore 35912 / 35913 Progressive Upright Vacuum ?

Doesn't suck I have a Hoover Empower. The motor runs, but it is not sucking anything up and the brushes aren't rotating.


Answers :

Every vacuum needs to be occasionly taken apart and throughly cleaned. Usually when the brushes don't rotae it's a belt. But sometimes it's because junk gets wrapped around the roller. Things like string or thread or fiber that wounds around the roller and actually eventually binds it so it won't roller anymore or move.
\015\012
\015\012Sucking problems might mean there is an object of some sort stuck inside an area you can't see unless you take it apart first. If it's not in the hose then it's probably in the dirt intake or other suction areas.
\015\012
\015\012I normally take my vacuums apart every 3-5 months and thoughly clean and wipe them down and am always amazed at their renewed sucking and pick up power right afterward even though I know that's why it wasn't cleaning as well.
\015\012
\015\012Unless it's a major motor issue just keep them cleaned and new belts handy.
You need too change the belt on the bottom where the brush is take off bottom cover and underneath is the belt if its broke replace it
Repair Help & Product Troubleshooting for Kenmore 35912 / 35913 Progressive Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Doesn't suck I have a Hoover Empower. The motor runs, but it is not sucking anything up and the brushes aren't rotating.


Every vacuum needs to be occasionly taken apart and throughly cleaned. Usually when the brushes don't rotae it's a belt. But sometimes it's because junk gets wrapped around the roller. Things like string or thread or fiber that wounds around the r ... Kenmore 35912 / 35913 Progressive Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Suction Problem I took my unit to my work and used it, when I returned home it wouldn't suck up anything. I took the recovery take out and it has inward suction. Shouldn't that be outward, so it goes into the tank? It also blows out of the bottom by the brushes. I check the filter in the bottom and that is fine. Is it possible that it is somehow reversed the direction of the air flow (rotor running backwards)? I am perplexed. What am I missing?


There is a stand pipe seal where the bucket sits on, and if it isn't there or out of place could cause a suction problem like you said yours is doing. In the picture it is #10. The motor seal may have gone bad and is leaking # 15.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.


Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Isn't picking up anything. it runs and the brushes run, but it's not picking up anything


Its loosing suction. most likely a clog ... iRobot Roomba 530 Robotic Vacuum

Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.


Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The brushes on my Hoover Stream Vac Plus will not rotate when it runs.


... Vacuums

The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up


Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.


It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums

The vaccum has been cleaned and checked but the brush is not rotating and no suction at the bottom, but through the hose. In reading the instructions to remove the brush cover it says to lift tab one and release 2-4. Where is the tab for tab 1 can not find anything for tab one to be able to lift, nothing there any ideas for help would be greatlly appreciated/


3 on the front and one on the back. where the belt runs ... Bissell 6594 PowerForce Bagless Upright Vacuum

Not sucking & runs when brush is turned on but not when brush is turned off.


... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

The brush stopped revolving. I don't see anything blocking. It sucked up a corner of a rug for a split second but didn't pull anything off of the rug, ie, nothing from the rug is in there. Do these have belts? I don't see that. vicki


Although I do not share the exact same model that you have, there is a belt in the one I own. \015\012\015\012Checking it was pretty easy as the unit comes apart in a simple manner.\015\012\015\012I do not know how your unit comes apart b ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Brushes at bottom of vacuum are not sucking up anything. It seems like its blowing out instead of sucking on the bottom.


Blockage somewear ... Dirt Devil Vacuums

Why doesnt my rootcycle dyson **** up! belt ok, emptied regularly, the handle bit where it sucks is fine but not the rotating brush. it sucks up fluff but not light dirt and bits. changed white pipe underneath as it was split.


There is a removable cover on the bottom of some Dysons which is like a U-Bend. On occasion this is a likely spot for blockages. Also make sure that all of your filters have been cleaned. Locate your local Dyson Customer Service from ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?


... Kirby Heritage II Vacuum

DYSON DC14 While vacuuming the living room, the rotating brush started making an awful loud grinding sound. We opened the intake port, cleaned the brush but to no avail sound still persists once you lower the vacuum handle in an attempt to clean. Was wondering if there was anything that can be done?


Take the bottom plate off and check the belt. Also, rotate the brush by hand - it should turn with only a moderate resistance from the belt, or very little if you take the belt off. If it is hard to turn, or if the belt is stripped-out right where it ... Vacuums

I accidentally sucked up a string. The brushes stopped rotating and the suction was low. I took the frame off the brushes, and the rubber belt came out. How do I re-attach the belt/fix this problem? It is a Bissell power force turbo upright.


You'll need to replace the belt. \015\012On uprights with rubber belts, the belts need to be replaced every 3-6 months due to the fact that since the belts are rubber, they stretch, and once they stretch out they decrease the rotational speed o ... Bissell Vacuums

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brushes don't turn. It runs and dispenses shampoo and water and sucks it up but the brushes stand still.I cleaned them and filter etc still doesn't work.


There is a plastic shaft on the back of the block brush (spin scrubbers),\015\012 these wear out or break. You may need to replace the block brush. Or if the shaft is not broken it could also be the Turbine Gear. This is \015\012what the block bru ... Hoover F7220900 SteamVac V2 Upright Vacuum

My husband sucked up part of a rug. The belt didn't shut off like I thought it was supposed to. Now there is a funny loud hum when the brush is running. There are also some fuzzy disc-like things around the brush that look like they're unraveling. Thoughts???


See if you can take the brush assembly off. There should be a plate and 2 screws. One on each side. You can lift out the brush and get all of the strings and such off of the roller brush. You might have to go a little deeper with it open and see if a ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Dc 35 runs sucks but no power in the floor brush


Hi there, it's Jack at Dyson. I'm sorry to hear your carbon fibre floor tool isn't running. You may want to follow the steps shown in the video below, just to make sure there are no obstructions which could be jamming the brush bar. Although ... Dyson DC35 Handheld Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0548 seconds