Having problems with your Kenmore 35912 / 35913 Progressive Upright Vacuum ?

Kenmore 35923 beltless brush not working after rolling up shlace.

\015 Kenmore Progressive with beltless drive, Handi-Mate Jr, model: 116 35923500. The lace was on a shoe so it stopped the brush. I have pressed the reset, and taken the brush out and used a volt/ohm meter to see continuity through the reset switch and brush motor terminals. The brush make a "jump" as a disconnected lead was reconnected to it's terminal on the brush motor (this was done when the power cord was unplugged). Made me think the component mounted in the brush motor rubber end casing could be a capacitor. I'm not sure what that component is or if it is working properly. With everything reassembled, the vac motor runs, the brush can be turned by hand, but it is not being turned by it's motor. Please, what is the fix for the brush?\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015

Answers :

Its due to the grip of the brush and the motor not getting fit its became little bit like streched so this happens and in this case replacing the brushes and checking any other component broken near to it is necessary.
 take out the air flow filter at the back of the vacuum and turned it on, somehow the clog cleared will get cleared . Then  put the filter back in and it will work  perfectly.\015\012
Repair Help & Product Troubleshooting for Kenmore 35912 / 35913 Progressive Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore 35923 beltless brush not working after rolling up shlace.


Its due to the grip of the brush and the motor not getting fit its became little bit like streched so this happens and in this case replacing the brushes and checking any other component broken near to it is necessary. ... Kenmore 35912 / 35913 Progressive Upright Vacuum

The brushes won't roll on my beltless Kenmore progressive upright vacuum


... Kenmore 34923 / 34925 Progressive Bagged Upright Vacuum

Kenmore Beltless Vacuum brush will not spin. Everything else works.


There is a reset button on the side of the lower base of the machine, plug in the unit turn on the switch to the brush and vacuum are both engaged hit the reset button, remember the roller will not engage when the handle is in the upright position, r ... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

The brush does not turn on my kenmore intelliclean beltless drive upright. how do i correct this?


... Kenmore Vacuums

We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work


If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.


... Vacuums

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha


You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

ProForce 1500 has suction but the brush roll motor stops working.


... Proteam ProForce 1500 Bagged Upright Vacuum

Eureka boss 5893A brush roll does not work


You have to prss the pedal and lean it back the brush roll wil enguage ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a kenmore beltless upright the beater brush dosetn spin


If it is direct drive then the motor or the wireing to the motor are bad. If it is gear driven then the gears are probally stripped. ... Windsor SR12 Sensor Bagged Upright Vacuum

The roll brush will not turn when on floor. Too much pressure stops brush. Changed belts and still not working


Turn the belt inside out. This problem stems from a design flaw in the mechanism that turns the hoover from bare floor to carpet. After taking it apart I realized that the spring that pushes the belt tight (to make roller spin) is not any where nea ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I have a Kenmore Central Vacuum Type K Model s107. The system will not work with the short handle, therefore I can not use the adapter brush ect. It will work when it is connected to the long handled main attacment. Any suggestions on how to fix this problem?


... Kenmore Vacuums

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis


Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Have a kenmore cannister vaccum, brush is working but it is not picking up anything the suction is not working ?


Remove the hose and clear any obstruction from inside of it. If that does not work check the bag and filter if one is installed ... Vacuums

On my Dysen DC 24 Ball the ball is not rolling easily and the brush feature is not working. Is there a repair center near the 94941 zip code?


This modle not easy replair if unit have warranty you send service for free.\015\012Bestbuy store\015\012..\015\012MARIN CITY CA (Store 132)180 DONAHUE STMARIN CITY, CA 94965Phone: 415-33 ... Vacuums

Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run


If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum

Brush roll not working on hoover upright U6455-900


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=700283\015\012Generic problem for all Vacuums\015\012Brush roll not working on\015\012Posted by archies ... Vacuums

Cord got into brush area. pulled cord and now rollers will not turn. Beltless drive Vacuum kenmore 3 years old 11635922500


Greetings,Your Kenmore Beltless Drive upright model 116.35922500 has an overload protection system designed on it. This will prevent anything from damaging the brush motor, or your roller brush if you were to vacuum up something in it (i ... Vacuums

In my kenmore progressive vacumm cleaner the brush is not working


... Kenmore Vacuums

I have a Dyson DC17. Everthing appears to be working but when I set it in motion I hear a loud screeching sound. Sounds like a belt on the brush roll cover but the roller still spins.


The belt might be worn and causing the sound. Here is the belt you need and the manual:Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brush roll on my Eureka Bagless The Boss 4 dimension cleaning vaccum itsn't working. How do I fix it?


Take either the plate over the brush roll off, if it doesn't come off, then the top cover comes off, should be 2 or 3 screws on the top to remove. Then you can get to the belt and brush roll. Check the brush roll, make sure the ends turn freely, if ... Eureka Vacuums

Kenmore canister. Brush is turning but spitting all dirt under and out the back of the head. I guess the suction is very weak or non at all. What is reseting overload protector doesn't work. Haven't tried yet but just in case. THANKS!


I would look to see if there is a clog. that would be the only reason that the power head would be spitting dirt in back of the power head. check the hose. ... Kenmore Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1014 seconds