Having problems with your Kenmore canister vacuum 116.21714110 ?

How do I repair the wiring in my telescoping wand.

The Power Mate (carpet brush) does not turn on and the light at the end of the wand no longer works.

Answers :

Repair Help & Product Troubleshooting for Kenmore canister vacuum 116.21714110

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Telescopic wand My wife's Electrolux Oxygen has a telescoping wand that expanded and contracted. All one had to do was slide a button and the lower tube slid inside the larger upper tube. Now the button no longer moves whatever was inside to allow the expansion/contraction to happen. How do I fix this situation? The wand assembly hardly seems to be made with repairs in mind. This method of manufacturing is annoying. Thanks, Eric


... Electrolux Vacuums

The hose with wires still attached has disconnected from the wand inside. How do you reattach the hose to the dc22 telescopic wand?


... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

The spring assembly popped out of the electric head telescoping wand? Is this repairable or is wand available as separate part for purchase?


Replace wand ... Beam Industries 2775 Serenity Plus Central System Vacuum

Miele Filtration Guard S528 Canister Vacuum telescopic wand repair


Hi There, you certainly can get a ... Miele Filtration Guard S528 Canister Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.


Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available


Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?


... Euro-Pro NV31 Infinity Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to dismantle twin clean powerhead to repair broken wires? the wires to the pc board have broken but can't seem to be able to remove plastic cover over wires without breaking cover.


... Electrolux Twin Clean Bagless Canister Vacuum

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.


Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?


Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

Can't lock my telescopic wand


... Vacuums

Where can I purchase a replacement wire for the handle of my aerus centralux hose? It's the black wire that runs from the switch in the handle and attaches to the pins in the wands.


Any Aerus Electrolux store should have them in stock.\015\012You can find the one nearest you by following the directions on the below site:\015\012\015\012 ... Electrolux Centralux Vacuum

Wiring Schematices Hello, Thank you for posting the wiring schematics on FixYa. Those are the ones I needed. However, I cannot make them out on the webpage. So, if you could kindly send me a copy to my e-mail address, it would b highly appreciated. Prefferably in .pdf format if possible. Thank you very much. Desperate To Repair Kent


I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. T ... Oreck XL Ultra Bagged Upright Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?


Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

Titan therm o dial T770 wiring diagram space heater I need wiring diagram to make repairs


... Vacuums

My telescopic wand height adjustment won't lock the height in place. The wand extends to full height with no locking in place. How do I fix it?


These wands have a very small nub that locks them into place. They wear out very easily. You might have to replace the wand. ... Euro-Pro NV31 Infinity Vacuum

I just want a wiring diagram as the wiring is a bit messy from past repairs its had only 2 motors operating and i want to put teh 3rd motor back in.


I am not too sure of what you are working on. If you give me more information then I should be able to help. Thanks!!! ... Vacuums

How do you put the telescopic wand down? Just got a new dyson 17 and I cant use it cause I cant get the dang wand down..


Make sure your handle is snapped in all the way on to the machine, that will release the clip on the hose to allow for the wand to slide in. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Electrolux telescopic wand stuck in up position


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My miele s2 momemtum electric wand is broken, won't stay locked in position. It is telescopic.


... Miele Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0248 seconds