Having problems with your Kenmore Magic Blue 24195 Bagged Canister Vacuum ?

My magic Blue vacuum is turning off and on when the hose ifs moved I think

\015 It will run for awhile then goes on and off\015

Answers :

I would recommend checking where the end of the hose attaches to. On Kenmore vacuums where the end of the hose plugs into the vacuum and to the powerhead there is normally two prongs that plug in to the canister and the power head. It is either one of the ends that is not connecting right especially if you say when the hose is moved. It may also be the cord inside the hose that connects to those prongs might be torn inside the hose or not connecting right to each end.
Repair Help & Product Troubleshooting for Kenmore Magic Blue 24195 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My magic Blue vacuum is turning off and on when the hose ifs moved I think

I would recommend checking where the end of the hose attaches to. On Kenmore vacuums where the end of the hose plugs into th ... Kenmore Magic Blue 24195 Bagged Canister Vacuum

My magic Blue Vacuum keeps shorting out it seems that when the hose changes position near the base it turns off and on by itself

... Kenmore Magic Blue 24195 Bagged Canister Vacuum

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Magic Blue won't turn off - Kenmore Magic Blue 24195 Bagged Canister Vacuum

... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

Hi: We ahve a Tornado CV30 vacuum. The suction does not seems to be working properly. There is no suction at the tool hose and the bag does not seem to have air moving into it. Do you think there is a clog somewhere? The roller is moving. Thank you for youre help :) Kelly Branson, Mo.

To clear the clog, remove the hose and wand from the unit and separate them. The hose is\015\012released by pressing the white plastic ring in the housing. The two are\015\012separated by simply unscrewing them. Remember this threaded connection\015\ ... Tornado 93030 Wide Area Carpetkeeper Upright Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?

Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

No action Hi: My brush roll won't budge. After we cleaned out all the hoses and replaced a badly worn belt (burned?) when I turn it on the smell of burning rubber and smoke has continued. What hurts is that I don't think I've used the vacuum a total of 10 times ... and I had such high hopes. Ideas?

I had the same problem with the belt breaking and the roller not spinning. I read about giving the roller a couple of revolutions to seat the belt, so I put another new belt on. It still didn't spin. I realized it was the end cap that was not spinnin ... Eureka 2961AVZ Bagless Upright Vacuum


... Kenmore Vacuums

My vacuum is not sucking theirs a yellow pellet that indicates the air flow. And when i turn it on it moves and i think thats part of the problem i don't know what to do i lost my manuel help.

Try emptying bag. then clean filter. then unblock hose using a broom handle. let us know how it goes. ... Hoover Vacuums

The hose has no suction and shrinks up so that it can't even be put back on the vacuum w/o turning it off. I have checked everything that I can think of and don't see any blockage anywhere. I washed the filter about one month ago and I clear it at least once a week.

Just happened to me. Took everything apart. No blockage in the flexable tubing or connections then I looked down the hard, telescoping tube and saw that it was occluded. Everything's fine and dandy now. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to open the kenmore blue magic vacuum - Kenmore Magic Blue 24195 Bagged Canister Vacuum

... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Change bag in magic blue vacuum - Kenmore Magic Blue 24195 Bagged Canister Vacuum

... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?

... Easy Flo EF2300 Central System Vacuum

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.

Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

The brush on my Hoover Windtunnel T series won't turn when I'm vacuuming carpet. It does, however, turn when I'm vacuuming bare floor, and I didn't think it was supposed to do that.

1) test the belt +brush for worn and replace2) test the motor God bless you ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

No vacuum My Floormate has plenty of air moving, but no vacuum at the nozzle. When I turn it on, the filter hops up to the black rubber "intake", rather than staying in its spot. It seems to me that the intake should be in contact with the filter when the reservoir is installed. And I don't understand why the intake isn't closer to it, but it seems fixed there, almost an inch higher than the filter. When I remove the bottom reservoir and turn the h3000 on, I feel vacuum at the intake, and air

Someone must have lost the filter cover from the machine. It is a clear blue plastic cover that goes over the filter and has a hole that lines up with the motor intake. It is approx. 3 inches square and has an angular top to coincide with the motor i ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I was vacuuming with an attachment, the vacuum began to loose suction and the hose collapsed, then the vacuum stopped running. I have turned it off and continue to plug it in off and on, using different plugs. It will not turn back on.

Hi there VacuumGuru for www.vacuumspot.com.au here. You have got yourself a blockage in the hose is all. The reason it wont turn on is because that machine has a thermal cut o ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have an old Miele canister vacuum and I do not know how to disassemble the hose to check for a clog. I think it sucked up a nerf ball the size of a ping pong ball. I changed the bag but it did isn't appear to be in the bag. The vacuum powers on but I do not have suction with the hose, and since the hose has hard plastic elbow joints I do not want to pry them apart and break it

Hi Emily: If you have the model number for your machine you may be able to find your manual on the Miele website. Check ... Miele Vacuums

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@

Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1375 seconds