Having problems with your Kenmore Magic Blue 24195 Bagged Canister Vacuum ?

Kenmore vacuum #721.24195500 How to change belt?

\015 The foam filter inside bag area ripped and I think something got caught in there ? strange grinding motor sounds ? can I fix this myself?\015

Answers :

Repair Help & Product Troubleshooting for Kenmore Magic Blue 24195 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to change the belt for kenmore heavy duty plus extra wide sweep model no. is 1163966180 looking for manual how to change the belt


... Vacuums

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

How do i change my Kenmore upright vacuum belt?


... Kenmore 33721 Upright Vacuum

Belt I have a Kenmore canister vacuum and I need help changing the belt


You probably need a phillips screwdriver to Remove the screws on the bottom of the vacuum and pull the brush bar out _ the belt is wrapped around one end of that and anchored to the vacuum - put new belt on and replace cover on bottom by replacing th ... Kenmore Vacuums

I have a kenmore vacuum cleaner that I bought a new belt for butcannot get the bottom off to change the belt. Model # 116 53312305


... Kenmore Vacuums

My question earlier today referred to a Kenmore Progressive upright vacuum. Your answer suggested that I change a belt, if the reset button did not work. Does a direct drive really have a belt? Regards, Jim Buckley


Direct drive does not have a belt. It is a shaft with gears. What is wrong with your vaccum? Maby i can help. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Change the belt in my kenmore power-mate 120 amps...how to open it to get to where the belt is???


HELLO, JUST REPLACED THE BELT ON OUR'S. FIRST TAKE LITE LENSE OFF THERE WILL BE 2 SCREWS, REMOVE. THEN FLIP OVER POWER MITEON EACH SIDE PRY WITH 2 SCREW DRIVERS WHERE THE ARROWS ARE TO SEPERATE & THERE IT IS THE BELT. MIKE ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

How to change belt Kenmore Progressive 300?


... Oreck XL2200 Bagged Upright Vacuum

How do you change the belt on a Kenmore Model 31164 vacuum


... Vacuums

Remove powerhead case on Kenmore #116 53500300C to change belt


... Kenmore 25512/ 25513 Progressive Canister Vacuum

How to change the vacuum belt on a kenmore heavy duty plus model number 203966180


... Kenmore Vacuums

Chang the belt in my kenmore power mate power head


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore elegance: how do I open it up to change the belt?


A picture is worth a thousand words, so the diagrams in this manual should be helpful:..35622 Owner Manual ... Vacuums

I cannot get the Kenmore power-mate open to change the belt? How does it come apart?


... Kenmore Vacuums

How to change the belt on a kenmore cannist


... Kenmore 25512/ 25513 Progressive Canister Vacuum

How do I change the belt on my Kenmore 12 amp upright vacuum


... Kenmore 33721 Upright Vacuum

My Kenmore Progressive keeps burning up belts even after I have changed the bag, cleaned the filters and checked to make sure the agitator was clean and free turning


On the left hand side, just above the handle release, is a lever to adjust if you are doing hard wood or carpet cleaning. When adjusted for hard wood, that lever releases the belt and just uses the "vacuum" function. When set for carpet it engages ... Kenmore Vacuums

How to change a belt??? - Kenmore 34723 Grab-N-Go Upright Vacuum


... Kenmore 34723 Grab-N-Go Upright Vacuum

How to remove cover on Kenmore canister vacuum model 116 in order to change belt?


... Kenmore 35912 / 35913 Progressive Upright Vacuum

How do i change the belt on kenmore upright vacuum


... Kenmore 35622 Upright Vacuum

I have an older model kenmore upright 30475. how do i change the belt on it.


... Kenmore Vacuums

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.


Its still clogged, you gotta dig deeper ... Vacuums

Kenmore Whispertone How do I change the belt?


The cover over the light, push in on the sides to release the tabs, then remove 2 screws. Using a screw driver, put it in the slot, one on each side, from the bottom, pry up to release the tabs, cover will come off and you can get to the belt and br ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I need to change a belt on my kenmore progressive 360 canister vacuum.


... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0683 seconds