Having problems with your Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum ?

I have a kenmore upright vacuum model #116.35922500. The agitator tube doesn't turn. It doesn't have a belt for the agitator. It has an overload protector. I reset it, but it keeps poping back up. Should I replace the overload protector?


Answers :

The reset is for your safety no belt ,probly a direct drive motor issues ,maybe the brushes it is detecting a short and pops the reset.
Repair Help & Product Troubleshooting for Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore upright vacuum model #116.35922500. The agitator tube doesn't turn. It doesn't have a belt for the agitator. It has an overload protector. I reset it, but it keeps poping back up. Should I replace the overload protector?


The reset is for your safety no belt ,probly a direct drive motor issues ,maybe the brushes it is detecting a short and pops the reset. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

How do I reset the Kenmore "overload protector reset" button? It is quite loose and doesn't want to click back in.


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Kenmore canister. Brush is turning but spitting all dirt under and out the back of the head. I guess the suction is very weak or non at all. What is reseting overload protector doesn't work. Haven't tried yet but just in case. THANKS!


I would look to see if there is a clog. that would be the only reason that the power head would be spitting dirt in back of the power head. check the hose. ... Kenmore Vacuums

My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Problem with powermate nozzle keeps tripping. hit overload reset and the lite comes on and starts to work but within 5 seconds shuts down again...help


... Kenmore 22313 Bagged Canister Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

The thermal motor protector on sears model 116.35912 Kenmore vacuum won't reset. The manual says to wait 30 minutes and the thermal protector will reset on it's own. It appears I would have to take the vacuum apart to get to the thermal protector. Is it worth the effort or should I trash the vacuum?


... Kenmore Vacuums

Motor on our kenmore progressive agitator is not


Look for a reset button on the motor and press it in. If it clicks, then it was tripped. An excessive load on the motor can make the reset trip. Try turning the motor shaft to make sure that it is not bound up. Run the machine empty for a short time ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Agitator stopped rotating, has checked for clogs, cleaned agitator, and pushed reset button, but still not rotating. Any ideas?


Try changing the belt ... Vacuums

Why doesnt the belt turn the agitator bar?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks


... Sunbeam Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Agitator does not spin, light does not go on


... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

Bissell Healthy Home Vacuum No Power - Reset Thermal Protector?


Try to re-install the handle. On occasion if the handle is not installed properly and secured tightly the unit may experience intermittent power. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

My Model is a U5465-900 - I need to replace the agitator housing.


I don't seem to be able to find a site with entire replacement parts list. Or a cross reference to the U5465-900 model. It has a 15" agitator. The housing has been "rubbed" through at one side of the agitator and is no longer capable of contain ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a new Kenmore magic bued and I am about to change bags for the first time. Trying to do this the clip that is supposed to hod the bag close to the whole keeps coming off when I replace it and close the lid, turn on the vac the sucction is very low and it keeps showing the bag is full which is not true / what is going wrong here ? Thanks so much for supporting, Beba


Sorry to hear that you are having problems with you Kenmore Magic Blue.There is a so-called "bag full indicator", which will only turn red if it got some major blockage. This is the reason why there is no power suction.The "fu ... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Problems with Kenmore Whispertone model 118 Bagged Canister Vacuum Overload Protection Reset won't reset


... Kenmore Whispertone 23312 Bagged Canister Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I need to know how to replace a agitator brush for a Hoover Fusion model U5180 900. I was given the vacuum, but without the manuals, so I have no instruction on how to replace the brush. I have already purchased the new brush. Thank you for your help


Please use the following link.\015\012http://www.hoover.com/pdfs/manuals/U5180900.pdf ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

How can determine when it's time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I'm cleaning? Thanks, Jim


Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck! ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

I have a eureka power paw that keeps breaking belts. there doesnt seem to be a part that keeps the belt in place


My belt keeps breaking too, but worse is that I can't find out the size for replacing. Who knows the size I need for the Eureka Power Paw? ... Eureka Vacuums

Keep replacing belt that drives brusher but keeps breaking. When feel belt driver rod it is superheated.....could it be melting into the stretched belt causing it to weaken?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=559226\015\012Generic problem for all Vacuums\015\012Keep replacing belt that drives\015\012 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0516 seconds