Having problems with your Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum ?

I have unscrewed all the screws and can't get bottom off.

\015 I sounds like there is a clog somewhere. It does pick up but not like normal. Sounds loud. Have new filters. How do I take the bottom off?\015

Answers :

Here is a possible solution. If the vacuum sounds normal when the green light comes on, then the issue is a suction bypass. Kenmore built a suction bypass in to help cool down and protect the motor should someone either never clean the filter, empty the canister or somehow manage to clog the hose. There is a spring holding the bypass closed and is overridden by vacuum suction. I guess the spring becomes weak, allowing high suction to pull it open which in turn reduces suction so it closes again. It can do this several times per second making a loud racket and slightly affecting performance until the sensor goes green, then the vacuum suction is too low to overcome the spring tension thus why it sounds fine then. The trick? The very hard way (what I did) was to open the vacuum, open the casing where the spring is and pull it apart slightly to increase the spring tension. The easy way is to put tape over the hole where the bypass is. The inlet is under the hose track on the back on the right side as you're looking at it. The hole is about the size of a quarter and you'll see fins across the hole. The tape would keep the suction. The motor would still pull back the bypass but since tape is applied, there would be nothing to reduce the suction thus keeping performance and reducing the noise. However, this circumvents the intended design so you do so only at your own risk.
Repair Help & Product Troubleshooting for Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have unscrewed all the screws and can't get bottom off.


Here is a possible solution. If the vacuum sounds normal when the green light comes on, then the issue is a suction bypass. Kenmore built a suction bypass in to help cool down and protect the motor should someone either never clean the filter, emp ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cant get the bottom plate back onto my dyson upright DCO7i


You need to press hard and turn till they lock inhttp://www.youtube.com/watch?v=fN8k--LbuCs ... Vacuums

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.


... Kenmore Progressive Direct Drive 30912 Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.


Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.


... Vacuums

My brush is no longer working on my bissell healthy home vac. when i try to turn it on it makes a high pitched squealing sound. I'm pretty sure it needs a new belt but my husband is having trouble getting the vac. apart. He says you need a special tool to get the screws out of the bottom of the vac. Any advice? THANK YOU!


Hi,\015\012 According to Bissel, they should be standard phillips screws. Nowever - things change.\015\012This is a general guide from Bissel for belt change - \015\012 ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The instructions, maintenance, said to unscrew the bottom to empty refill tank. I cannot screw it back because the piece it screwed into can not come out. It is inside the machine. Will this hurt the machine if I use it?


No you can use it like that, it will be fine. ... Vacuums

I caught a shoelace in the vacuum and now the roller won't go around. Is there a belt I can replace and if yes, how? I unscrewed 4 screws on the bottom but it won't come apart. Do I force it? Thanks Shari


With the screws out the base plate should come off. There is a belt and the one you need you can get here:Hoover Flair Upright Replacement Belts ... Hoover S2200 Flair Upright Vacuum

How do I clean out the suction side of a Hoover steam-vac Model#f6020-900. I took all the screws out and still cant get it apart.I vacuum before using it, but it still seems to find more hair.


These don't come apart. Hoover makes a thin long tool that will allow you to stick up into this suction side to clean it or use a long piece of galvanized metal strip to slide up into it and clear away the hair. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Was vaccuming and vaccum quit. Tried unplugging and turning back on. Getting absolutely no power. unscrewed screw under handle and tried to make sure connection was being made. Don't really know what to do.


Ok..If you have a multimeter you can check plug fuse then switch and motor, if you put leads across the plug you will get some reading if its working.could be thermal cut out on the motor. ... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Need to change the motor on dc07 how do you get the motor out I have loosened and taken out all the screws and still cant disconnect the power cable in


Have you looked at www.dysonmedic.com ?\015\012\015\012It has a really good feature on changing a DC07 motor. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do i get the case off the hoover studio 1400w i can find 4 screws but the top will still not separate from the bottom


... Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.


HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

Vapor Clean TR 5 Under "maintenance" they told me to unscrew to empty refill tank. After doing that, no water came out and the piece that the scew went into is now in the tank. It is too large to get out and even if you put the screw back inti that piece ir still goes into the machine. Can I still use the machine? brand new only uded it once


I is really needed to check this with the manufacturer! See contact details below: ... Vacuums

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!


... Hoover Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi there Hi have a Samsung VCU2913 Bagless Upright Vacuum. The wheel at the bottom have a rubber where it is driven by for the brush to clean the floor. Where can I get this, its n new vacuum... now I cant use it. I am in SA , Pretoria


Go back to where you bought the vacuum and ask for a BELT. Take the MODEL # with you and buy 2. Always keep a spare ... Samsung Vacuums

HOW DO YOU CHANGE BELT CANT SEEM TO REMOVE BOTTOM TO GET TO IT KENMORE WISPERTONE 116


The top cover to the light lense pops off at the ends. When you get that cover off then you will see 2 screws that are by the swivel neck. Take those out and then the whole body top cover comes off. That will get you into the roller brush and belt ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0445 seconds