Having problems with your Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum ?

How to take the brush out?

\015 A string is stuck inside the left side of the brush of my Kenmore Progressive Bagless. How do I take the brush out to remove the string?\015\012Thanks for your help.\015

Answers :

This is actually incredibily difficult on this vacuum because of the no belt, dual motor setup. Try cutting the string from the outside without opening the vacuum.
There should be screws on the bottom plate covering the brush roll, take those out and it should come off and then you can access the brush roll.
Repair Help & Product Troubleshooting for Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?


You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced. ... Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan


I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

My Roomba says to clean the brushes when the brushes are already clean. Is there something to take apart to check? I have already taken the brushes out. I don't know the model number, I think it's the 500 series, black and silver.


Turn the unit upside down and remove the bottom pan should be 4 or 5 screws depending on the model. next remove the 4 screws that hold the brush cartridge and pull the whole brush assembly out.using a can of compressed air cle ... Roomba 3005 Pro Robotic Vacuum

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

How do I take the brush out?


Most of these progressive drives have a bottom plate that you can take off, then you can get to the brush roll asm. There will be several screws. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Vacuum brush Well thank you for your response but how do you remove the brush cover plate? I looked to see if I could unscrew it but i dont see any screws. I don't know how to take it off


... Kenmore 22812 Bagged Canister Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?


I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Sebo X4 is squealing when pulled back. Takes a while after it's been running for this to happen. We changed the roller brush (needed it anyway) but didn't take care of the noise. Could the wheels be making this sound? At least that's what my staff thinks is going on... I own a commercial cleaning company and all we use are sebos... they're an amazing machine!


Yep - we think Sebos are pretty good too. I work at a Sebo sales and repair dealership! The wheels are a good bet - I can't think of anything else that might cause the noise. If in doubt, I suppose you could simply wheel one around for a while when s ... Sebo X4 Bagged Upright Vacuum

I cannot get the brushes to turn, now here is a dumb question does it take a belt as I am not seeing one on the brushes


Yes it does take a belt. This belt needs to be replaced every 6 to 12 months. Here is the belt you need and a manual with instructions:Bissell P ... Bissell 6594 PowerForce Bagless Upright Vacuum

I'm trying to clean the brushes under neith and trying to figure out how to take to plastic part off so that i can clean underneith. I think the brushes come out but i'm not sure how.


The brush block wasn't made to take apart and clean. The whole block will come out, it just cames catches that hold it in place. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How to clean the bissell shampooer brush head on and need to take brush off to get out dirt and dog hair


Http://www.bissell.com/images/UserGuides/66Q4_109.pdfSee page 19 of the User's Manual for complete instructions. ... Bissell 8910 ProHeat Clear View Upright Vacuum

Brush Hi I just bought a Kirby second hand. There is a small black rubber belt hanging off the brush. How can I take apart the bottom part of the vacume and where does this belt go to. Thanks Anita


Check out my step by step instructions...\015\012\015\012http://reviews.ebay.com/CHANGING-T ... Kirby G4 Bagged Upright Vacuum

The brush is not spinning. I feel sucksion but the brush part is not spinning. I am hoping that I can take it apart but I do not have the manuel.


The belt needs replacing ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?


I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis


Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

This concerns Kenmore Progressive vacuum 21637115700 part 23 2CKG352000, the belt driven brush bar. I had to take it out for some serious cleaning and it expanded in length about a quarter inch as it is supossed to, I guess. How do I collapse it back so I can re-attach the belt and brush? Thank you


Hello. i can assist you. the bar will collapse back in one of two ways either direct pressure exerted on the ends or by a twisting motion applied to one end and or the other. use a pair of pliers or a wrench to get a grip on it if you need to. re ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0440 seconds