Having problems with your Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum ?

My kenmore direct drive with intelliclean vacuum brush is cutting out depending on the angle when in the unlocked position


Answers :

Repair Help & Product Troubleshooting for Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kenmore direct drive with intelliclean vacuum brush is cutting out depending on the angle when in the unlocked position


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a kenmore progressive 359235 vacuum with intelliclean. Has been great for about 3 years but now the brush bar has stopped turning. This is a direct drive unit with a circiut breaker reset button on top . The button is not tripped. Any ideas ?


... Kenmore Vacuums

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes


(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the


Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

The brush does not turn on my kenmore intelliclean beltless drive upright. how do i correct this?


... Kenmore Vacuums

The brush on my kenmore progressive direct drive intel clean won't turn


... Kenmore Vacuums

Dyson dc15 brush bar turns intermittently depending on angle of vacuum


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Kenmore 31913 Progressive Direct Drive brush not spinning


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My Dyson Animal is not picking up very well in the drive position. With the hose the pick up is still very good. I have had it for 2 yrs now with very little problems. I have cleaned out all areas etc pipes, the brush underneath and cant find any blockages. The noise of the dyson is the same as usual. Could you tell me if there is a part that it sounds like it needs?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brush is not rotating - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum


Try pushing the reset button with a pen or paper clip. If that doesn't work, the motor may need to replaced. If the reset button is stuck, I don't know how to fix it - mine has the same problem. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How do I replace brush - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum


Hi,Replacing the brush roller of a Kenmore Progressive upright vacuum is a job that can be accomplished in just a few minutes. The Kenmore Progressive vacuum uses a motor-driven brush roller and does not have a belt, which reduces the mai ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Which Kenmore vacuum cleaners are made by Panasonic? Are all of their direct drive machines made by Panasonic? We have a blue Hoover Windtunnel with the dirt sensor. It cleans well, but it is unbelievably noisy. I wondered if something was out of place and the brushes were hitting, but everything looks normal. We bought Kenmore models 36722 and 36724 and love them. I believe they were made by Panasonic. Our Kirby sits in the basement. Much heavier. These are quiet and clean well. I would like an


Some Kenmore vacuums are made by Panasonic, some are made by Hoover or Eureka or even Sebo. I would go to a Panasonic dealer for that kind of machine instead of trying to go by the Kenmore brand. Sears has a hard time with service. A good Vacuum C ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Rotator brush not spinning. Handle is not in the locked upright position. Says it's beltless, so is this likely an interlock switch or drive motor problem ?


Hi, the brush roll will only spin when your handle is not in the locked upright position, once the handle goes upright - the brushroll de-activates ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a progressive direct drive Kenmore Model # 21637100800 and the brush does not spin. I can't find a reset button. is there one? TIA


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Kenmore 116.35922500 brush wont turn. Seems to come on if handle angle is held at just the right position but it is intermittent. Reset button is not popped up and doesn't seem to have any effect.


... Kenmore Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Brush isnt turning kenmore progressive direct drive. mod 116.35923502


... Vacuums

Brushes don't move. vacuum motor works - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum


The brushes on the roller are driven by a wide, short rubber belt. These belts get old, worn, overheated, and break periodically.It should be a fairly simple matter to unscrew & remove the plate, revealing the belt and roller assembly. Yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.


Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Kenmore direct drive will no longer self-propell


There may also be a reset button. If the brushes get stuck the unit can shut off power to the brushes to keep a total melt down from occurring. The reset button should return power in these types of vacuums. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0760 seconds