Having problems with your Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue ?

Kemore Progressive Vacuum 116.35923500. Where is the switch that turns on the agitator roller. It will only turn on if the handle is laying flat. When I lift it up slightly the roller turns off. Bill


Answers :

Repair Help & Product Troubleshooting for Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kemore Progressive Vacuum 116.35923500. Where is the switch that turns on the agitator roller. It will only turn on if the handle is laying flat. When I lift it up slightly the roller turns off. Bill


... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ


I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

Bissell 6590 the part I am trying to replace allows you to lower the handle to lay flat to get under furniture and it also allows the handle to stay in the upright postion. i have looked on bissell.com and did not find it-but I will try again. you are super and Thanks allot . Have a super easy day! Michele


It is called the detent lever part # 2030052. If you can't order it from bissell.com or over the phone, most repair shops should be able to order it for you. ... Bissell 6590 CleanView Bagless Upright Vacuum

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?


This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I accidentally sucked up part of a blanket with my DC-17 Animal Dyson and now the roller brush makes a griding noise. Did I ruin the clutch or the roller bar. When I lift up on it slightly it doesn't make the noise only when resistence is applied.


My Dyson started making a loud noise when in "carpet" mode. After reading a ton of forums I thought it was the clutch assembly. Got a new one on eBay for a great price. Somewhat hard to replace, but thanks to this YouTube video, I was able to get it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Eureka Boss 4870 -Brush roller won't turn on carpet and turns when its not supposed to (with handle in upright postion). New belt had burning rubber smell right away.


... Vacuums

My bissell 9400's brush rollers do not stop turning. When I was using the hose attachment for the stairs the handle was in the upright position and the brushes kept turning. Also water was leaking out of the rear right side onto the the carpet under the machine.


... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

I have a brand new hoover canister s3755 and the beater brush will not turn on the carpet it spins fine as soon as you lift it slightly off of the floor, I can't imagine it is the belt as the mac


It's commonly the belt when they're new. More explained here:http://www.vacuummedic.com/blog/2012/10/09/my-brand-new-vacuum-doesnt-work/Call Hoover and complain, they'll likely send you a new one. The service centers will not ... Vacuums

Dyson dc 23 animal. the roller in the head will not turn when the vacuum is flat on the carpet as though it is sealed to the carpet


... Dyson DC23 Animal Vacuum

My Oreck XL was working fine, then when I vacuumed a shag rug is started smoking and smelled like something is burning. (I changed the bag, checked for clogs--none found, and roller brush is turning. It has a metal handle.) Now I am afraid to use it.


Even though the brush is spinning, the belt is probably worn out and stretched. when you vacuum the shag carpet, it puts more drag on the brush. try running it on a shorter carpet or hard floor for a few minutes. if it doesn't smoke, then you know i ... Oreck XL2000 Bagged Upright Vacuum

I want to brush the pile up on my carpet do I need a special attachment to do this??. I have shampood it and it still seems a bit flat. When I shampood no water/foam filled up in the front tray???I am sure I had attached everything correctly. The only thing I can think of is when I attach the brush and tray to the front of the machine, do I turn the handle back to the right way up, or do I leave it upside down, this is the one that picks up the belt.


Here's my online guide for using the Kirby shampooer....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Rollers won't turn when on carpet, ok if I lift the vacuum above the carpet.


That is very strange. So when you lift it up above the carpet the feet / wheels turn freely, but when it is on the carpet it won't move at all? Not even when you push it, the rollers won't turn, but when you lift it up it does? That doesn't make m ... Bissell 3920 Bagless Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took


... Vacuums

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher


If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?


You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

After replacing the flat bet and v belt on my Hoover model U6433-900; serial No. 12300043057, purchased June 23, 2004, the brush roller still does not turn when I release the foot lever to vaccuum.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=725351\015\012Generic problem for all Vacuums\015\012After replacing the flat bet\015\012Posted by maha ... Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Kenmore progressive bagless brush roller won't turn


Sounds like the brush belt is worn or torn ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh


Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.


Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Bissell Lift OfF Brush Roller Stops Rotating


They make the worst machines, the rollers are cheap and they make it so you cant take them apart to clean them. You don't want a dyson either, they aren't any better for pets. With all that hardwood floors you should get a good canister vacuum, sebo ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hoover WindTunnel Canister: Roller brush motor not turning


These motors have a fuse incorporated in the field winding and it sounds like that blew. These motors sometimes overheat at the front bearing and the bearing will melt into the plastic housing. This will cause the fuse to blow. It sounds like that's ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0583 seconds