Having problems with your Kenmore Quick Clean 30012 Vacuum ?
I have power to machine because light comes on but motor does not turn on.
Most of the time when your brush headlight comes on and the motor does not its inside the motor compartment, could be a loose wire to the motor or a bad motor
Repair Help & Product Troubleshooting for Kenmore Quick Clean 30012 Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have power to machine because light comes on but motor does not turn on.
Most of the time when your brush headlight comes on and the motor does not its inside the motor compartment, could be a loose wire to the motor or a bad motor ... Kenmore Quick Clean 30012 Vacuum
We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.
The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn't seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill ... Vacuums
Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like
I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums
Kenmore vaccuum upright moded#721.33289030 vaccuum worked just fine turned it off for a minute turned it back on the light comes on but theres no power from the motor Please Help thanks Valerie
Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on
... Miele Blue Moon Bagged Canister Vacuum
I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks
... Bissell 3750 Lift Off Bagless Upright Vacuum
I have lindhaus activa 30. It was clogged and then cleared of the clog. When the power button is pushed, both red and green lights come on and the green turn off immediately. But no motor....
Motor might be burnt up from the clog. ... Lindhaus Activa 30-38 Bagged Upright Vacuum
I only know this model as the Classic, but the colour of the canister in the photo is the same. The machine will not turn on, but when I retract and pull on the cord, the power light comes on briefly. Is there a short? I lent the vacuum to my daughter and perhaps she was rough with the cord.
... Miele S758 Bagged Canister Vacuum
Hi, A few days ago I bought a Philips hairdryer (HP4935/22) & have used it only twice. Somehow when I used it this morning some of my hair got caught in the filter at the back of the dryer & the motor slowed down & I think overheated & stopped. Normally the filters come off but I don't think this one does. I haven't turned it back on so as not to possibly damage it even more. I am quite upset as I really love this hairdryer. It's quiet, light, small, powerful & does the job brilliantly. I h
This is usually a safety feature so it doesnt burn itself. If there is a lot of hair in there try pulling it out, and if there is a little try with it too, if you can try get it out with something. If you think there isnt any in there anymore, try to ... Philips Vacuums
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos
It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum
My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off - seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance
As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair ... Dyson DC05 Bagless Canister Cyclonic Vacuum
REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu
Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums
Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?
Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum
My Kirby G6 light is not turning on when I start the machine. I took off the front piece and removed a lot of hair from the roller and interior. Since I did that, the belt keeps coming off (even though it is fairly new). Is that the reason the light won't turn on? Is there any advice you can give me before I take it in?
The light indicates that the brushroll is spinning. If it isn't coming on, the power nozzle may have been reinstalled incorrectly. Take the nozzle off and then use my step-by-step guide to reinstall it. I expect that it will take care of the problem. ... Kirby Vacuums
Motor problem machine is smoking/burning smell coming from the bottom of the machine. Motor still turns but doesn't make much sound; and soulution won't squirt. The model # is 1970
I had to throw the machine away before it burned my house down. There is no way to fix it; had to replace it. ... Bissell 1770 Quicksteamer II Upright Vacuum
Power going to the sencer light but motor don't come on
Drive Motor is gone or the control board. ... Windsor SR12 Sensor Bagged Upright Vacuum
I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.
Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i
At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum
I was using my Heritage 11 vacumn with the hose attachment and the motor shut down like the power went off .When you push the switch on the housing the light comes on but the motor does not run.
Hi, the motor could be overheating. Most vacuums have a heat sensor that shuts the vac. off if there is a clog. Let it sit, feel if it's hot. If so you may have a blockage of dirt etc. Try to clear it, let it cool and tart it up. I hope this helps, i ... Kirby Heritage II Vacuum
When I plug in my vaccum the power light turns on, but i get no power to the machine??? I changed bags and filters and still nothing??? Can you help?
That light wire is attached to part of the wiring that is just a piece attached to the main wire coming from the switch. Your bags and filters have nothing to do with powering the machine. You may have a bad switch or there may be a ground wire off ... Vacuums
SHARK STEAM CLEANER S3325. RED LIGHT DOES NOT COME ON WHEN POWER SWITCH IS TURNED ON. YELLOW LIGHT IS ON ALL THE TIME. DOESN'T HEAT UP NO STEAM. HELP!!!
... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum
On my kenmore central vac no power unplug unit plug it back green light comes on but try turning vac on green light goes off again .
Please clarify that we are talking about the central vac LED/switch panel panel and plugging it into a 110 V wall receptacle. If I understand when you unplug from the power source ,then plug back in the green LED comes on, looking normal ? But ... Easy Flo EF1400 Central System Vacuum
When you turn on the machine the light goes green,I then switch the lever over on the top to red for a hot drink,the machine makes the noise and you think its going to make your drink but no water comes out,My son brought it for xmas last year and didn't think to keep the reciept. thanks lisa
Turn off ... Vacuums
Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?
... Miele SEB 213-2 Vacuum
Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ
I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums