Having problems with your kenmore vacuum ?

how to put back together after cleaning out

the order to put pieces back together

Answers :

Repair Help & Product Troubleshooting for kenmore vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

I opened up my self charging wall hand vac to clean out the dust & can't get it back together - where can I take it to have them put it back together for me. It's only 6 months old? I live in Barnegat, New Jersey. (Ocean County)


Try Discount Vacuum Center in Manahawkin. They maybe able to help you out, if not, be able to suggest where you maybe able to go.\015\012\015\012Discount Vacuum Center\015\012(609) 597-1119 \015\012 ... Oreck ElectrikBroom AV-701B Handheld Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I cleaned the filter of my Dyson DC16 and after I put it back together it won't recharge


Hi Fayez,I'm sorry to hear you're having difficulty with your DC16. It's probably best if you give our Helpline a call so we can resolve this for you as quickly as possible. One of our advisors will be happy to run through some troubleshootin ... Dyson DC16 Bagless Handheld Cyclonic Vacuum

Cleaning and reassembling a Jarvis Walker Ultra Power 5500 reel and need help putting it back together. Are there any schematics for this reel online?


... Vacuums

How do I put it back together I took it apart to clean it. Can't get it back togather,, HELP!!!


Here is some videos that should help you ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Have cleaned and pulled apart the rainbow vacuum Model D4A. Put it back together now there is no suction. Which way do the fans go back on? Do you have any diagrams of layout?


... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Bissell 1623-1 Steam Cleaner. It will work good for about 2 minutes and then after that it will not dispense cleaning solution on floor or through the hand held wand.I have replaced both drive belts with no improvement. I have cleaned it and found no obstructions in hoses and spray nozzles, put back together and it still will not dispense. Is it possible the pump or solenoid is no working? Aaron


... Bissell 1623 Steam Cleaner

I recently acquired a Sunbeam SA12587 water cooler/dispenser w/refrigerator Model#YLR2-5-90HZ3. I took it apart to clean it and now i can't figure out how to put it back together PLEASE HELP!!!!! it's been sitting like that for a week!


... Sunbeam Vacuums

Throughly cleaned roomba of dog hair, including taking off gears. After putting back together the brushes no longer move. Any suggestions


Try turning manually about 20 turns and re try, might have to do a couple of times, make sure no hair caught under yellow tips ... iRobot Roomba 560 Robotic Vacuum

WE TOOK IT APART TO CLEAN IT AND CAN'T GET IT PUT BACK TOGETHER


What brand? ... Vacuums

No motor when switched on two red lights flash,cleaned hoover, put back together motor started,then cut out after a few seconds


I would double check your wiring, Make sure all wiring is tight. No cracks, no pinched wires. If needed, bypass the switch and see if it will stay running. If so, switch would be bad. If it's the same, then you have a wiring problem or a worn motor a ... Sebo Automatic X1 Bagged Upright Vacuum

How to clean turbo brush of harmony electrolux and put it back together properly


Wait, there are two more screws that must be removed before the top shell will come off. They are located under the wheels. Pop the wheels out by simply inserting yoru finger or a small tool into the wheel and pulling straight up. Remove those two ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

I took the vacuum apart, and cleaned the filter, cannister reservoir, removed all the hair which was wrapped around the beater bar. One the filter was dry (next day), I put it all back together. Now, there is no suction, and it sounds differently than it did before.


Check its assembled correctly . Sounds like something is out.... ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the "bag" compartment and when I look they are just all gathered in a clump in the bottom by the brush.


Hi.\015\012\015\012Remove the sole plate turn the 3 plastic screws to unlock & lift off.\015\012\015\012Now remove the blockages that have accumilated from the oppening of short clear hose.\015\012Check you can turn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

HI, I HAVE ELECTROLUX LE(similar to 2000). I HAVE TAKEN IT APART, CLEANED IT, AND PUT BACK TOGETHER. IT SEEMS I GOT THE WIRING WRONG. CAN ANYONE GIVE ME A SIMPLE WIRING DIAGRAM FOR THIS VAC? THIS MODEL HAS NO CONTROL KNOB. IT'S NOT COMPICATED BUT I MUST HAVE CROSSED SOMETHING BECAUSE IT SHORTS OUT NOW. HAVE CHECKED ALMOST EVERYTHING ELSE. THANKS.


... Electrolux UltraLux 2000 Bagged Canister Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I took my vacuum cleaner apart to clean it because it was clogged inside and now I am having trouble putting it back together. I am looking for a manual of some kind to show me how to assemble it. It is a Kenmore Progressive Model # 11636933502


... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor


On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum

What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th


A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums

I have a suction problem with my Shark Navigator vacuum cleaner. I tried to clean it and after trying to put it back together, it lost suction. What can I do go get it working again?


... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

I take apart and clean my DC17 every 2 weeks. When I put it back together it always works perfect. This last time, I noticed that the self propel is not working...am I missing something? I took it apart to be sure eveything is in it's place but no difference. Now I have to push really hard.Any suggestions?


The roller is not spinning do to motor or belt not working. If it is the motor then the machine will have to go back to dyson if it is the belt then that is an easy replacement. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0507 seconds