Having problems with your Kenmore vacuum model 116 27515700 ?

how do I remove the motor from my Kenmore model 116 27515700 vacuum cleaner

motor sounds like bearings are gone

Answers :

Repair Help & Product Troubleshooting for Kenmore vacuum model 116 27515700

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore central vacuum cleaner model number c107 34601. We have emptied the bucket and shaken the filter out to clean it. There is a filter that is filthy so we shook it out into a bag but the cleaner still seems to not have great suction. I notice there is a similar cap to the outlets I plug the central vac hose into on the unit itself that doesn't power the nozzle when used. 1 - what is this for? 2 - Should I somehow remove the entire filter and if so - can you tell me step by step ho

... Electrolux Vacuums

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

I have an older Kenmore vacuum cleaner - Model #3285590C, Serial #DG4117817. I can't seem to figure out how to get the motor cover off. 2 bolts in the front have been removed but the back has no visible bindings. It seems to be held from inside the compartment! Whats the catch here!

... Kenmore Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak

... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a kenmore canister vacuum cleaner, 4 yrs. old, model #116.27815701. The powermate assembly, the one for the carpet, seems to have a short or something. The light goes on and off and the motor

... Kenmore Vacuums

Removing kenmore vacuum Canister motor cover model 116-27312790

What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks

Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.

... Vacuums

Have a Sears model 116.59612991 vacuum cleaner that stopped working. Does the relay part #8174981 hane anything to do with it. Have removed the motor and it cycles on and off with power supplied to it.

Check the switch ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

How do you remove the back wheels from a Kenmore Model 116.2441290 canister vacuum cleaner? Do they just pry off?

... Kenmore Vacuums

The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?

Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum

How to take apart beater bar of kenmore vacuum cleaner model 116

... Vacuums

Needed, a new Hose for Kenmore Canister Vacuum cleaner. Model Number 1162497184 --A 3.9 Powermate Kenmore Vacuum Cleaner

... Kenmore Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

I have a Kenmore canister vacuum - model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** - no air flow. What could be the problem. The cleaner is only 4 years old.

The motor has an inline fuse ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.

Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth

When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Kenmore Progressive canister vacuum cleaner: MODEL # 116 27615700 When the vacuum cleaner is running, the performance indicator light is red (lit up). What should I check in order to trouble-shoot and solve this problem?

... Kenmore Vacuums

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank

You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

My Kenmore canister vacuum cleaner model 116.27514700 has unacceptably low suction.It is much less than my older GE Walmart canister vacuum. the 2 filters are very clean and there is no blockage in the hose and the dust collection bag is empty. Is poor suction a characteristic of this model or if not is there a way to fix this problem?

... Panasonic Kenmore Canister Vacuum Vacuum

Kenmore vacum cleaner model 11628615801 has power but vacum motor doesn't work

... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1330 seconds