Having problems with your Kenmore Vacuums ?

How do you take the canopy cover off of a kenmore cannister vac?

\015 How do you take the canopy cover off of a kenmore canister vacuum model 116.28412790 so i can replace the power cord reel?\015

Answers :

Flip the vac upside down and look for two screws from the underside near the wheels. If they are not visible you will need to remove hidden screws from above by prying gently at the back of the vac where the body panels meet at the bumper. Also look for two vertical screws in the bag area.
Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you take the canopy cover off of a kenmore cannister vac?


Flip the vac upside down and look for two screws from the underside near the wheels. If they are not visible you will need to remove hidden screws from above by prying gently at the back of the vac where the body panels meet at the bumper. Also look ... Kenmore Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

How to take apart wand of kenmore vacuum 116.24614400 to replace COVER #8191782 on Sears part


... Kenmore Vacuums

I have a kenmore cannister vac - model 27514. Do I have to use hepa bags in it, or can I substitute another type, and which would that be?


You know, any bag made for the unit should give similar results. You can buy a cheaper bag and that number is 50558. You can get them at your local vac shop or you can let me know, I will send you some. The price per 3 pack is only 4.95. The cani ... Vacuums

Owners Manual for Kenmore Whispertone 300 Cannister Vac


... Kenmore Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Have Kenmore 360 HepaFilter cannister vac. Belt not turning. Reset button doesn't seem to be functioning. Any suggestions? Thank you.


... Kenmore Vacuums

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

My kenmore cannister vac (model 116.27514) has a slight burning odor after operating for a few minutes. We have removed the hepa filter and it looks like there is a strip of foam curled up behind the hepa filter compartment. Could that be the problem? How do we access that area? Thank you.


... Kenmore 22822 Canister Vacuum

My Kenmore Quick Clean vac clogs at the top of cannister and does not let dirt to go to canister. After vacuum for few minutes have to stop empty before continuing to get rug clean. Is there anything that I can do to solve problem.


You need to own an air compressor,and blow out all vacuums ,after each use. ... Kenmore Vacuums

Removing kenmore vacuum Canister motor cover model 116-27312790


What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

Kenmore 116.2481190 vac I need help with replacing the hose


... Kenmore 22812 Bagged Canister Vacuum

Kenmore 25614/25615 Progressive bagged canister vac won't start


Sounds like there was a loose connection or loose wire that came in contact with another wire. check your cord for small burn holes, also could have shorted out in the hose or the wand. If you are comfortable to disassemble the vacuum i can walk you ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


Www.searspartsdirect.com ... Vacuums

No suction I am getting no suction on my central vac at the vac. I do not believe that the piping is plugged up, the vacuum is not creating suction. What are the causes of no suction at the vacuum and how do I take the top half of the Nutone central vac off?


Use the guide at builtinvacuum.com/flowchrt.html to find the issue and solution. Most likely you need to test it without any filter and be sure the bottom of the unit is attached :) To get access to the motors you need to unbolt the very top sides. ... Broan-NuTone CV350 Performance Bagged Central System Vacuum

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


... Alba Vacuums

I have a bissell bagless easy vac. When I vacuum the debris keeps getting stuck in the hose (also going into the filter area and the apparatus above the cannister with none of it going into the cannister. I have made sure the cannister is properly placed and the lock is pushed in all the way.


... Bissell 3102-0 EasyVac Upright Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

Shop vacuum float rises to shut off vaccuum immediately when turned on. Is using foam filter covered by Shop vac paper filter. Vac is shopvac 86L450


Click this link for video helphttp://www.ehow.co.uk/videos-on_4811_care-portable-shop-vac.html ... Vacuums

I have a kenmore upright model 116.36933 vac. motor wont stop unless i pull th plug the buttons work on everything else but stopping the vac


... Vacuums

Kenmore Quick Clean Advanced Allegen - The plastic screws (for the cover that houses the belt and beater bar) are broken. Is there a replacement cover?


Go to Sears.com, click on parts, put in your model number, a parts list is available, also a picture diagram of it. You can purchase what you need from this site. ... Vacuums

My 2001 miele stopped working Black cannister. I believe cleaning ladies overheated it as the bag was very full and the vac felt warm to touch. I replaced bag and let cool down but it will not start. This has happened before and the vac store said they replaced the cord because it tends to go when it over heats. I have not taken in for and estimate but I fugure it will be at least $150 to repair. Is the another option.


... Miele S548 Bagged Canister Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0425 seconds