Having problems with your Kenmore Vacuums ?

KENMORE 27614 CANNISTER VACUUM The roller vacuum brush does not rotate. I check the belt and it is fine. Waht could be the problem?

Answers :

Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

KENMORE 27614 CANNISTER VACUUM The roller vacuum brush does not rotate. I check the belt and it is fine. Waht could be the problem?

... Kenmore Vacuums

The roller on my Dyson vacuum has stopped rotating (I still have suction) I have checked the belt (not Broken) and have checked and cleaned the roller and spindle and also checked the "auto" button setting on the vacuum but to no avail ... Anybody have any clue as to the problem Many thanks

... Dyson DC07 Bagless Upright Cyclonic Vacuum

My eureka vacuum was fine but then suddenly got loud. We cleaned the filters and replaced the belts, but it is still loud. We have not seen any clogs in the tubing or in the vacuum. What other problems could the vacuum have to make it loud?

The noise could be coming from the Beater Bar's ball bearings. ... Vacuums

I have a power groom dual cyclonic vacuum. It is less than a year old. The belt is fine, It is not clogged. The brush rotates and it has suction. The problem is that it has the most awful high pitched noise now. Truthfully, the noise is so awful it makes you nauseus. What is the problem?

... Bissell 3920 Bagless Upright Vacuum

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.

This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum

My Hoover upright vacuum has gotten very loud. I have checked the roller, belts and hoses but I haven't found anything. What could the problem be? thanks

Most Hoover uprights are a "fan first" design, meaning that all dirt enters the motor , hits an impeller fan and is blown from there into the bag. You will need to open the vac, remove the belt and two C shaped clamps holding the motor in place and ... Vacuums

My kenmore progressive canister vacuum brush won't spin. I've checked the belt and it is fine. I've hit the reset button and there doesn't seem to be a problem there either.

... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?

I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

The power nasal has stopped working. I have checked the belt and is it fine. What could be the problem?

Check the cord going to the power head, if it is ok, then you may have a bad motor. ... Vacuums

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brushes are not rotating - checked the belt no problem - what else could it be?

Assuming a drive pulley is not loose and the motor turns, try turning the brushes by hand. If they require much effort they may be jammed by dirt. My cat is a constant culprit! ... Eureka 4700A Maxima Bagless Upright Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio

Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.

You need to replace the belt. Replacement Vacuum Belts ... Vacuums

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?

... Bissell 8910 ProHeat Clear View Upright Vacuum

We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!

These belts need to be changed every 6 months regardless of the way they look. ... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.

Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

Vacuum My vacuum is loosing it's suction power. I've checked the belt and it's in perfect shape...I've bought a new filter cup...I've checked for clogs and there aren't any...I've cleaned the entire machine...and I still can't find the source of the problem.

You checked the belt, but I bet it has stretched and won't drive the brush roll under load like it should. Belts only last a few months the stretch and should be replaced. Iff you have suction at the hose, then it has to be down below, either belt/ ... Eureka Whirlwind 4480 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1195 seconds