Having problems with your Kenmore Vacuums ?

I have an older model kenmore upright 30475. how do i change the belt on it.


Answers :

Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an older model kenmore upright 30475. how do i change the belt on it.


... Kenmore Vacuums

I acquired an older Kenmore upright vacuum (Model 116.38612790) - Cannot figure how on earth you open to check the belt. Help!


... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

How do i change the belt on my kenmore upright vacuum model 721.33079400?


... Kenmore 33721 Upright Vacuum

Changeing belt I have a Eureka Upright Limited Edition Model 4462D and can not for the life of me find my manual and can not find the screws to take off the plate to change my belt.....help!!!!!


On the top nozzle, there will usually is 2 screws holding the top done. There are slots or holes on each side near the front and the screws or in these holes. Remove them, remove the top cover and then you can get to the brush roll and belt. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

How to change the belt for kenmore heavy duty plus extra wide sweep model no. is 1163966180 looking for manual how to change the belt


... Vacuums

How do i change my Kenmore upright vacuum belt?


... Kenmore 33721 Upright Vacuum

Upright vacuum cleaner model dm4485 belt change assistance


... Hoover Vacuums

My question earlier today referred to a Kenmore Progressive upright vacuum. Your answer suggested that I change a belt, if the reset button did not work. Does a direct drive really have a belt? Regards, Jim Buckley


Direct drive does not have a belt. It is a shaft with gears. What is wrong with your vaccum? Maby i can help. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Need to change belt on hoover upright model u5093-900, but can't figure out how to open it up to get at the belt.


... Hoover Vacuums

Eureka altima model 2993 how to change belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a kenmore vacuum cleaner that I bought a new belt for butcannot get the bottom off to change the belt. Model # 116 53312305


... Kenmore Vacuums

Hoover upright model u5095-930 belt change


I couldn't find your specific model but this may be similiar to another that you have to position the new belt around the agitator (beater bar) on the bottom of the vacuum, replace the cover, and then turn the vac over and remove the TOP cover to lif ... Hoover Vacuums

How do you change the belt on a Kenmore Model 31164 vacuum


... Vacuums

How to change the vacuum belt on a kenmore heavy duty plus model number 203966180


... Kenmore Vacuums

Kenmore Upright Model 116.356224400. Belt


A picture is worth a thousand words, so the diagrams in this manual should be helpful:35622 Owner Manual ... Kenmore 35912 / 35913 Progressive Upright Vacuum

Kenmore upright vac model 33922 - good suction but developed loud whining noise after accidentally vacuuming room without bag. Added bag and changed both filters. Still makes noise. How can I stop noise?


The bag is the first stage in your filtration. Most times what you did will draw fine dust right through the filters and into the motor itself, affecting the bearings and clogging the motor fans, throwing them off balance. The fact that there i ... Kenmore 33922 Direct Drive Bagged Upright Vacuum

How to change on belt on eureka model # 2991 - Eureka 2991AVZ Bagless Upright Cyclonic Vacuum


Here is the belt you need and a manual you can view which has instructioins:Eureka 2991AVZ Belt ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

How to change belt in eureka altima vacuum - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Here is the belt you need to replace and the manual which has instructions:Eureka Altima Belts ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Have eureka victory upright bag vacuum model 4325 how to get into machine to change out the belt


There are four holes on each side of the top of the hood. There is a screw on each side, inside one of those holes. You have to take those two screws out to remove the hood. ... Eureka Vacuums

How to change belt on eureka vacuum 2996 - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The information you're looking for can be found on page 8 of the manual via this link: http://www.eureka.com/service/manuals/80244.pdf ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Change the belt on Model#4481 vaccume - Eureka Whirlwind 4481 Upright Vacuum


... Eureka Whirlwind 4481 Upright Vacuum

How do i change the belt on kenmore upright vacuum


... Kenmore 35622 Upright Vacuum

Need help need to change belt on a model #1489a upright vacuum cleaner.


... Eureka Vacuums

How do I change the belt on my Kenmore 12 amp upright vacuum


... Kenmore 33721 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1251 seconds