Having problems with your Kenmore Vacuums ?

The power head model #116. 53812300 does not stay on. When I push the belt reset button it only stays on for a second or so. The belt is not jammed or the roller.

Answers :

Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power head model #116. 53812300 does not stay on. When I push the belt reset button it only stays on for a second or so. The belt is not jammed or the roller.

... Kenmore Vacuums

Have an e-series rainbow. Belt and brush bar have been replaced in power head. But the red reset button can still be pushed and it is not staying going like it should. May it be the motor?

... Rainbow E series Canister Wet/Dry Vacuum

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.

Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

I have a kenmore progressive vacuum with a belt reset button that trips out everytime you try to vacuum. It does it in about 5 to 10 seconds. Can I bypass the reset button or can you help me determine the problem. Thanks

A lot of times the reset button is tripping because there is a problem. The problem could be with the brush roller in this case. A lot of times I see this unit for repair and the end of the brush is so compacted with hair and debris that it has also ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Dyson DC24 instructions say to push the red reset button for the roller bar. My vaccuum has no red reset button. Where is it?

... Dyson Ball DC24 Bagless Upright Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.

Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

Eureka Boss - Belt is not broke but brush will not turn. I have already turned it over - checked belt - and pushed the reset button.

The belt may look fine but they can still be stretched or worn and it won' turn the brush. Try changing the belt and see what it does. You can get Eureka belts here: ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.

Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

The motorized wand attachment keeps shutting down after 10 to 15 seconds after pushing the red reset button. I've thoroughly cleaned dirt/debris from around motor. Do I need a new reset switch? Thanks, Tom

Either the reset is bad or the motor is drawing too many amps and tripping the reset. Do you have an amp meter? Check the amps being pulled by the wand attatchment against the load recommended by the manufature, this is usually located on a plate som ... Rainbow E series Canister Wet/Dry Vacuum

Push the reset button

Sounds like a problem I had. However, I took the vacum head apart were the belt is to get to the switch that was sticking. the model # on this part is: \015\012\015\012Mel Rain/littel fuse\015\012742332\015\01211200000-04 ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Halo beater bar has quit working. bar (that belt is wrapped around) connected to motor is not turning. have pushed reset button. k.r.

Take it to an oreck dealer. duh ... Vacuums

The roller on my Dyson DC24 quit rolling. I've taken out the brush, cleaned it, replaced it, locked it and push the reset button but it still isn't rolling. Help!!! I've only had this for about two months.

... Dyson Ball DC24 Bagless Upright Vacuum

Loud grating/rattling noise comming from dyson dc04 when ever hovering upright as soon as i angle back the handle to push it. the belt has not come off, the roller is rolling and not jammed. sucks ok from the flexible hose.

... Dyson Vacuums

My kenmore progressive 360 needs the belt reset. I see a red button but nothing happens when I push it down.

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Every 3 swipes on the floor I have to push the reset button to engage the roller brush. Is this normal and if so why?

No, it is not normal for the brushroll to stop that often. You may need to clear any thread, etc from the brushroll underneath the vacuum. Remove the screws from bottom of unit, stand unit upright, turn height adjustment dial to either side to allow ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa

Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson dc25 schecking continuity on reset switch its a 91 series 2 amp switch but whether i have button pushed or not a get continuity shouldn't this break when button is pushed

... Dyson DC25 All Floors Bagless Upright Vacuum


We have only had our Navigator for 6 months and the bar won't turn. We took the whole beater bar head apart and it was a wiring problem in the beater bar motor.What a piece of junk this is, very poorly made and has many design flaws.Look ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

On button won't stay depressed. when pushed to on, the vaccuum goes on but won't stay on unless button is held down.

Needs a new on/off switch. You can order one from an appliance parts store, and replace it yourself or take it to a shop.\015\012\015\012Charlie ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.

It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc23 canister rug attachment loses power after about 5 seconds, push red button and restarts for less time. After 3 or 4 trys of it working for seconds it just doesn't turn on again. Reall

Hi Elizabeth, it's Jack at Dyson.I'm glad to hear you've been in touch already and we're able to resolve the issue under your machine's 5-year guarantee. In most cases, the issue you've described will be caused by something jamming th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?

Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0944 seconds