Having problems with your Kenmore Vacuums ?

It turns on and shuts off just like it is supposed to but the thing is bone dry. The humidity is at 56% so it should be able to dehumidify. It is just a little over 1 year old, help me please?!!


Answers :

If the machine's compressor runs when you switch it on, then turn the machine on maximum and let it run for an hour or so. Then check the coils in the back with your hand. If they are not getting cold at all, then there is a significant problem with the refrigeration process in the unit. It may have developed a leak and allowed your refrigerant gas to escape, or there may be another internal problem with the compressor. Either way you would need to have it serviced by a fridge technician, or more likely just replaced with a whole new unit since both options can potentially cost about the same.

If the unit runs normally and the coils are getting cold, then make sure they are not totally icing up which will impede the unit's performance. If your dehumidifier is freezing up then that probably means it is actually working well. The humidity level in the room is probably just relatively low and you probably have the unit turned up too high for the conditions.

Try turning down the setting on the unit so that it cycles on and off every few hours and does not run continuously.

Also try using some warm soapy water to clean off any dust or oily residue from the cooling coils in the rear of the unit. Remember to also clean the air intake filter while you are at it.

The ambient temperature in the room may also be a bit too low, so you can try adding some heat to the room if necessary. A dehumidifier will not work properly if the ambient air temperature is too low. Basically, the warmer and more humid the room is, the better they work.Since warm air rises, you can even try lifting the unit higher up off the cold floor onto a bench or table where the air is warmer.

You can click on the following link for a general operating and troubleshooting guide with additional tips on effective dehumidifier operation:

http://www.allergyconsumerreview.com/dehumidifier-advice-troubleshooting.html
\015\012I hope that was helpful to you, good luck.
\015\012
\015\012If you choose to rate this solution using the Thumbs Up scale provided, I thank you very much for your time and consideration.
\015\012
\015\012Joe.
Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It turns on and shuts off just like it is supposed to but the thing is bone dry. The humidity is at 56% so it should be able to dehumidify. It is just a little over 1 year old, help me please?!!


If the machine's compressor runs when you switch it on, then turn the machine on maximum and let it run for an hour or so. Then check the coils in the back with your hand. If they are not getting cold at all, then there is a significant problem with ... Kenmore Vacuums

Bought an PlayStation 2 at our youngest dauthers 9 year birthday together with an dance mat. Caused by an accident we had to buy a new remote contol for some years ago and we chosed your URC-3445. We can't get it to work. How do we get to AV-chanel throughtout your device? There must be a solution at our problem. Please help ....! Her anniversery is unfortunally today!!! Our TV is an rater old Tandberg modell: TVF2915NT Please...


Go to menu settings, find channel edit or add/delete, turn channel to input or a/v channel, select add channel and then your good. You should now be able to use the ps2. You can also hook them up through vcr and use the vcr input/av channel. and then ... Vacuums

Dyson animal We bought a Dyson Animal from Sears a few years ago along with a service contract. We took it each year to be serviced. One year I took it because it lost it's suction. They sent it to the factory, but it came back still not working right. We did the same procedure over ands over many times than I can remember. I now have the cleaner in my garage and am using my old vacuum because I just can't seem to get anywhere with Sears. Please help me. We paid almost $600.00 and now it can't b


As someone who works for Sears, let me just say right now.. The service contract you bought sucks.. and does not really do anything for you. it was just a wast of money ( they have a new one now.. thats so much better because you get your money back ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

HOOVER SAVVY This is less than a year old (yep, no receipt) and all of a sudden last night the vacuum turns off after a moment of running. Also the red and green lights do not work at all. I've thoroughly cleaned the bagless unit, and it still won't work. It powers on for a split second then turns itself off. Help please.


I had the same problem. Took it in and the repair shop they said it was the switch. It was an $18 switch and $30 labor. Switch was a red on/off button with 2 wire leads and caps to screw on for connection. If you can wire a ceiling fan then this ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!


... Hoover Steamvac F5860-900 Vacuum

The suction in the hose of my 2 year old Dyson Animal vacuum is compromised. I may have sucked up a small cat toy or something. Regular vac still is fine. The hose "sucks closed" after a few seconds near the top. I love my Dyson! Please help.


Hi there, it sounds as though the wand handle is blocked. To test this, remove the wand handle from the hose and test the suction at the top of the hose. If its strong here, then you will need to remove the blockage from the wand handle. If the suc ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a problem with my Shark Euro Pro Electric Flatiron. I purchased it a few years ago and can't locate my manual to find out what to do. The steamer button doesn't want to press down all the way so just a little steam comes out instead of the full one like it should. Please help!


... Vacuums

My dyson animal vacuum (~9 years old) will not stay on. I press the on/off button and it will only stay on as long as I am holding the button down. Help please!


Hi it sounds like you need a new switch ... Vacuums

I have a 4 year old pink dyson that I've loved until recently. It's always been easy to unclog when it wasen't picking up-now it seems maybe a seal problem has occured. The suction is making a funny noise and just not picking barely anything up. I'm getting talked into an expensive Oreck--please help!


\015\012Thanks for your response.First: (This is most likely as you say the suction is making a funny noise.) The DC07 has a short length of clear plastic hose on the underside of the machine. Check this very carefully for splits (pull it ... Vacuums

I have a DC17 which is only one year old. Today I lost suction and called for assistance. A Dyson technician told me to pull off the wand and see if it is clear. It was clogged so cleared out the obstruction. My filter was cleaned more than 24 hours ago. The vacuum still has no suction. Is it dead, any other suggestions. Please help.


Take the hoses off and give them a good shaking.\012or get a long piece of stiff wire and gently poke through the obstruction. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

12 year old husqvarna orchidea sewing machine needs part number4122282-01 can anyone help please


... Vacuums

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

HA-871? I'm not sure if anyone can help with this, but I've got a **** Smith brand HA-871 alarm system which I haven't used in years. When trying to get it working, not only have I forgotten the code but I can't remember how to enter it (as in, 4 digits and a #, or just the 4 digits, or something else...?). As I am able to get into the alarm box with the key, does anyone know how to reset it and enter the code? I can't find the manual either. Thanks to anyone able to help with this!


Incase you are still interested you set the code with the four jumpers inside the unit.\015\0121st digit is the brown wire\015\0122nd digit is red wire\015\0123rd digit is orange\015\0124th digit is yellow ... Vacuums

Either of my bissell porheat turbo 2x or my bissell pro heat don't have suction i would like to try and trouble shoot if i could due to the fact i am having difficulty finding a small machine repair center in my area could you possible help me or send a link which could help me find solution these machines are not more then a year and a half old if that thanks for your time and help warmest regards rebekah majors


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I am an athletic coach and use four Terrain 550 radios and assistants to help coach, moniter and time athletes at various distances away from me. I would like to be able to communicate with the athletes directly, both ways, but have not been able to find a suitable headset unit to use with these radios. Please can you arrange to supply or recommend some headset units compatable with these radios? Even better, units with mikes to enable the athletes to run relatively hands free. Many thanks f


You can try these links 1. http:// ... Vacuums

Hi, I have a Casio fx-115s scientific calculator which I've had for around 25 years. I am unable to use the bracket function and have lost the instructions. Could you please give any advice to save me having to buy a new calculator? I'm not sure how to use the brackets, whenever I press the ( ) buttons, it shows -E- on the screen which I'm presuming is an error message. Please help.


You should be able to use parentheses in the same order in which you would write the arithmetic expression. For example, 4*(3.5-1.5)= should give you 8. Without the parentheses, this would 12.5.Essentially, the left parenthesis comes imme ... Vacuums

Help ok the diagram is helpful but i have a black wire that came loose from somewhere it has a little prong on it does it click back in opposite from the white let me know please


I am not sure what exactly you are referring to but I think that it may be a motor lead. See pictures below (shown is white but second wire to the motor is black) ... Rainbow E series Canister Wet/Dry Vacuum

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

I have a Bissel Pro Heat Plus and I used it once, one year ago. I may be using it wrong, as my carpets were wet and there was no return (dirty water). If I remember correctly, going forward wets and cleans the area and to dry the area you move backwards. Please help, as I can not find my manual anywhere (which is not like me). HELP!


It has only one tank that serves two purposes. It holds the clean water and collects the dirty water, so you only have to empty/fill one tank. If you check reviews of this machine you will see that they basically stop working correctly aft ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I purchased a used Minuteman 2400 series buffer/burnisher over the weekend from a store that is closing. The unit is about 7-8 years old. I did not get a manual with this item, can you help me out with this. I would like to read up on it so if I have problems I can look back on it. Even as far as the operation of it would help to have a book for it. Linda


I have this manual available via email. chris321 at gmail. ... Vacuums

I recently took out a stand mixer that is probably over 50 years old. It belonged to my mother and I wanted to use it. It probably hasn't been used in at least 10 years. With some effort, I removed one of the beaters but cannot remove the other one nor can I even budge it. I have used WD-40 but it's not helping. It's a Westinghouse product. Any ideas? Thanks.


If you used WD40, you should have the unit inverted so the WD40 runs down into the beater socket.Use a small piece of wood and place it against the bottom of the beater and tap lightly with a hammer while pressing the beater release button/lever, jus ... Vacuums

Very little suction on my dyson dc24 yellow ball upright . only 21/2 years old.. should i take it to a vacumn repair shop ? it has a 5 year repair guarantee. I cannot find the papers. But i know that i filled out the guarantee & miled it in. what should i do?????


I'd look at this:\015\012\015\012http://www.fixya.com/support/t2827418-very_little_suction_in_hose_no_tears_in ... Dyson Ball DC24 Bagless Upright Vacuum

The belt keeps coming off. There is a little U shaped metal piece that came off when the belt first came off. Where does it go? When we first got the vacuum, we sucked something up and the belt came off and that little metal piece fell out. The belt now periodically comes off when we bump something. Please help us!!!!!!!!!!!!


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


Www.searspartsdirect.com ... Vacuums

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


... Alba Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0480 seconds