Having problems with your Kenmore Vacuums ?
Replace part #8191782 on kenmore 27914 vacuum
\015 Trying to replace part #8191782 and need to know if it is ok to cut the ribbon/cord holding the old one in place\015
Repair Help & Product Troubleshooting for Kenmore Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
We have a kenmore canister vacuum, the part that is attached to the wand that picks up the dirt doesn't work, when it's on the carpet the light does not go on. Do we need to buy a new vacuum or is there a replacement for this part.
Hard to say without the correct model number.\015\012\015\012However, you could check these things first:\015\012\015\0121- Is the belt that runs the brushes on the end pieces broken? If it is, is needs to be replaced.\015\0122- Is there ... Kenmore Vacuums
The foot pedal on my Kenmore upright vacuum cleaner has broken three times. The vacuum model number is 116.33923 and the Sear's part number is 8174906. Does Sears make this part in metal instead of plastic? It is becoming expensive to keep replacing this piece when it costs around $20 each time (including shipping) Thank you for your time. Jerry DeWulf
We have a Kenmore Grab-N-Go Upright Vacuum with a Hepa filter. We lost the yellow filter canister that goes in the top of the vacuum and need to replace it and the filter that goes in it. Is there somewhere we can purchase a replacement part?
... Kenmore 34722 Grab-N-Go Upright Vacuum
Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.
I have a Kenmore Elegance vacuum and need a part number for a replacement hepa filter. Vacuum model is 116 30306400C. Thanks.
Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks
Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums
A family member recently gave me their Kenmore Vacuum Cleaner (model 35821) and I did not notice that the power cord was missing at first. I tried to look closely at the manual online to see if this was something I would be able to purchase or if the vacuum was no longer any good. Do you happen to know if there is a replacement part for the actual power cord for this item?
Any power cord 17 gauge or lower will work ... Vacuums
Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan [email protected]
Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum
The dust bin on this vacuum has cheap plastic parts. anywhere where I can replace it in its entirety? Kenmore only provides the parts separately and the total is over $70. One screw was nearly $4...which gives u the idea.
... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum
Replace part #8191782 on kenmore 27914 vacuum
... Kenmore Vacuums
How to take apart wand of kenmore vacuum 116.24614400 to replace COVER #8191782 on Sears part
... Kenmore Vacuums
I'm replacing part # 8175156 cord reel on my Kenmore canister vacuum. How do I tension the spring? Do I do that before winding the cord onto the reel?
I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!
... Kenmore Vacuums
Kenmore canister vacuum 25812500 hose end replacement
... Kenmore 22822 Canister Vacuum
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I'm using a Eureka maxima 12 amp vacuum and where the hose is connected to the vacuum by a screw that part is broken where do I find a replacement hose that includes the clear plastic part that I can attatch to the vacuum?
... Eureka 4700A Maxima Bagless Upright Vacuum
Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a
... Hoover S3670 Bagged Canister Vacuum
I have a lawn sprinkler system that has a main inlet valve that opens when the sprinkler is run. This inlet valve failed after a recent long freeze when water retained in the valve became ice and then expanded. Questions: 1. Can I replace just the plastic parts that broke or do I have to replace the total valve? The valve is made by FEBCO,CA and the following is written on the valve: 4010387; 765-PUB; B 6412 and 150 MWWP. 2. Where can I get the valve or the parts? My zip code is 77479 and I ca
Yes you can, take the piece into home depot they can help with it. usually you can replace the total valve as awhole , its easier to do it this way, and still cost effective :) \015\012\015\012press add a comment in upper right corner if ... Vacuums
SEARS KENMORE CANISTER VACCUM, Model No. 107-23050, Volts 120AC, Type AV, Hertz 60, Amps 11: This is a small model vaccum with an on/off switch on the canister. The on/off switch has gone and the vaccum can only be used by plugging and unplugging it. I am looking for the replacement on/off switch part but Sears Kenmore has no listing for this vaccum or parts. I can't recall just how long ago it was purchased but could be 10 years (or more). As this model is perfect for the application neede
The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.
No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums
We own an ElecktaPure Exclusive Edition EP-4000 cannister vacuum cleaner and we are having a heck of a time trying to find replacement bags for it. We could not find the original part number of a suitable replacement part number. Can you help?
... ElektraPure Vacuums
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum