Having problems with your Kenmore Vacuums ?

Handle release pedal 401.39030900 - Kenmore Vacuums


Answers :

Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

My kenmore progressive vacuum handle release pedal fell off how can i fix this


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Handle release pedal 401.39030900 - Kenmore Vacuums


... Kenmore Vacuums

The red handle and release pedal fell off my kenmore model 116.23107C vacuum cleaner. how do i reattach it?


... Kenmore Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Handle release pedal replacement on Dirt Devil Reaction vacuum


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

How to replace handle release pedal on dirt devil kinetix self propelled vacuum cleaner. I need to remove the broken pedal and replace it with the new one.


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

How to replace handle release pedal on dirt devil kinetix self propelled vacuum cleaner. I need to remove the broken pedal and replace it with the new one.


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?


You can buy Hoover Handle Release Lever 38434-021 at \015\012http://partsreadyonline.com/item.php?ItemID=798 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Where is the handle release on a Kenmore upright vacuum


... Kenmore 33078 Bagged Upright Vacuum

Replace handle release pedal Kenmore 116.35923500


... Kenmore Vacuums

Need to preplace handle release pedal - Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum


To remove the old pedal, simply insert a screwdriver along it's outside edge, and pry upward to pop it out. The new pedal, (#38434026) can be pushed into place with your fingers. Install it with the handle in the upright position. ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.


It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

How to replace a handle release pedal on kenmore 25614/25615


... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

How to replace vacuum handle pedal release on hoover dm 5530


... Hoover Vacuums

DM4470 001 Hoover Vacuum Cleaner. How do I remove the "Handle Release Pedal"


... Hoover Vacuums

I have a Hoover Windtunnel Dual V. The vacuum and I did a tumble down stairs and the handle release pedal was broken. Is that something I can order a part for and have my husband put on? If so, where would I obtain the part? Thanks. Roxanna Kindler [email protected]


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=627747\015\012Generic problem for all Vacuums\015\012I have a Hoover Windtunnel\015\012Posted by ekindl ... Vacuums

How do you replace the handle release pedal - Eureka Smartvac 4870 Bagged Upright Vacuum


The handle release is just snapped into the bottom base. To take it out you will need to take a flat screw driver and pry the old one out. Then take the new one and pop it into place. ... Eureka Smartvac 4870 Bagged Upright Vacuum

The handle release pedal wasn't allowing the handle to lower. I took off the pedal and saw the spring load part was broken. What is this part and how to replace it? Bissell 3760-3 handle release


Our vacuum recently had an issue with it's motor, we had to borrow a neighbors a couple times while we were trying to figure out what to do. We decided to take it to a place that specializes in cleaning supplies and cleaning tools to see if they had ... Vacuums

Kenmore 31913 Foot pedal release lever broken-need to replace


FixYa techs - thank you for your response but I solved the problems. It took me 2 hours of continual searching but I finally found the parts - listed under the tab sew machines of all things!? There is one pedal in stock and I called t ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Dirt Devil vacuum Release pedal not working


Take off the bottom like you are replacing the belt. You will find a little metal clip that controls the upright lock.  It may be lose or broken. ... Vacuums

I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!


... Sharp Twin Energy EC-TU2607 Vacuum

Need new handle release kenmore 401.39035900


... Vacuums

The red handle and release fell of my kenmore model 116.23107C vacume. how do i reattach it.


... Vacuums

Bissell 3595 handle release pedal spring(?) missing


I just fixed this on my Bissell PowerForce model #6594 vacuum myself. Woo Hoo for me. :-)\015\012\015\012I called the local vacuum repair guy and he told me he'd repair it for me if I insisted but that since my machine only cost about $80 ... Bissell 3522 PowerForce Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0747 seconds