Having problems with your Kenmore Vacuums ?

35923 roller works intermitently

\015 Roller stops and goes during operation. There is no obstructions.\015

Answers :

Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

35923 roller works intermitently


... Kenmore Vacuums

Roller does not work. My vacume works fine , but the roller does not work. How can i fix that/


Remove the brush assembly, and clean/oil (3in1 or similar) the end bearings. If the belt is broken/damaged, replace same. Install the belt on the roller and motor shaft, then install the brush into the vacuum base--make sure the belt is half twisted ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen


Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.


... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

When I turn the vaccuum on the roller works for about 20 seconds, then I hear an awful, loud noise, and the roller does not work. Sounds like maybe some gears are being stripped? Please help


It sounds like you need to change the belts. You can get replacements and view the manual here:Dyson DC07 Belts and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.


Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Nothing inn the canister after using,suctione working,bottom roller working,no air leaks from hoses.Also when running awhile it shuts off by itself,have to wait awhile to use again


I'm not sure what vacuum you have, but that sounds like a blockage to me. Thermal shut off kicks in, shutting the motor down, to prevent damage from overheating. After waiting like 1 hour it probably comes back on. Make sure hose, filters, bag (if an ... Vacuums

Simplicity synchronicity brush roller and headlamps not working, hose still works. Only used brand new vacuum for 10 minutes before it stopped working!


... Electrolux Central Vacuum

Brush works intermittedly - I've looked at the common solutions listed but none seem to work...shaking it & reseating the canister will get it working again sometimes but obviously that doesn't seem to be a very good solution. Can you help?


I just had the same problem. I would turn on the vac, and it worked fine. When I turned on the brush it would work for a few seconds then shut off. Through troubleshooting I found out it had nothing to do with a bad power connection. By chance I took ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Upright cleaner BUC11700GB. Roller will not rotate, belt intact roller free. Have removed cover and roller motor not working when switched on.


... Bosch Vacuums

Roller I recently removed my roller to cut all the hair off it and when I replaced it everything snapped right in but when I turned the power on the power worked but the roller wouldn't turn


Hi.\015\012\015\012Did you put the drive belt back on the roller ? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Vacuum motor is not working but the roller is working.


... Hoover S2220 Flair Bagless Upright Vacuum

Eureka the boss 5893A brush roller will not work


Is there anything jammed underneath.can you turn the brush roller by hand.if not then take it back where you bought it.sounds like you have a defective brush roller ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The roller brush stop working


The fuse in the plug may have blow so replace it any ways ... Dyson Ball DC24 Bagless Upright Vacuum

Rollers work, wand sucks but the bottom doesn't ****?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Eureka 431BX suction stopped working. Roller still goes. Please help! Everything else is working great.


Even though the brush is spinning, you probably need to replace the belt\015\012because ... Eureka 431BX Bagless Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

My seb0 automatic x1 roller have stopped working . there is nothing stuck in it . the suction part is working perfectly. can you help please?


\015\012Almost certainly you've got a broken drive belt. This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at ... Sebo Automatic X1 Bagged Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I am hoping my Kirby Sentra has a reset button. It is only 5 months old and it will not turn on.It worked a couple hours ago. The vacuum will work with the hose attachment but not with the roller.


... Vacuums

Dyson DC14 roller doesn't turn but everything else works. The belt is on correctly, the roller is clean and it turns manually so I can't figure out the problem.


The DC14 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" and "carpet". The roller will turn only when the knob is on "carpet", and even then only when the handle is tilted back ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0584 seconds