Having problems with your Kenmore Vacuums ?

116.28390 kenmore canister vacuum disassmbly of motor housing


Answers :

Repair Help & Product Troubleshooting for Kenmore Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

116.28390 kenmore canister vacuum disassmbly of motor housing


... Kenmore Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

My kenmore progressive canister vacuum turns on only if the hose is attached to the floorwand. It seems that the canister motor is not working because I can't hear anything coming from the caniste


If the floor wand is powered, there may be an electrical connection that is broken when the wand is disconnected. This is part of the design, not necessarily a fault ... Vacuums

I Have a kenmore 116.23612300 canister vacuum which will not start. I have power everywhere but nothing going to the black wire to the motor. Seems to stop at the pcb asm, #KC86WBZRZ000 . Nothing from there to the black motor wire. White wire to motor has continuity everywhere it should. Ruled out just about everything but the PC board. What does it do exactly?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I was given a Kenmore progressive hepa filter 22313 Bagged Canister Vacuum recently, but don't have the manual. We used it once to vacuum the house and it worked beautifully. Then we used it 5-6 days later and it started whining and getting hot. What year was this vacuum manufactured? Where can I download an owners manual?? Help!


Http://www.managemylife.com/mmh/owner_manuals/5461/KENMORE-Vacuum-Canister-L0809572 ... Kenmore 22313 Bagged Canister Vacuum

Removing kenmore vacuum Canister motor cover model 116-27312790


What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore progressive access motor - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Motor wont start on my kenmore intuition 116 - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I bought a Kenmore canister vacuum, model 116, in April 2007. This morning, the sound of the motor suddenly began to deepen, and I began to lose suction. Normally, if something is clogging the hose, the motor will wind up to a higher pitch, not a lower one. The filters are clean, the bag is empty, and I can't detect anything lodged in the hose. If this were a car's engine, I would say it's "lugging down". Any pointers?


Okay, bear with me. Is it possible you have a suction adjustment, dial somewhere on vac. Check and see and if it does, be sure it's all the way up. Also, try removing hose and run a broom handle fr. one end to the other...BUT be careful not to stretc ... Vacuums

I have a Kenmore Progressive Upright Vacuum - Purple, and it worked just fine. I emptied the canister (like always) and put it back in place. I turned on the vacuum to it immediately shutting down (motor) and only the lights come on. There is no movement/noise/suction at all! Any suggestions? I have tried everything. I have no idea why it did this.


Make sure that something didn't fall into the fan assembly in the base when the canister was removed. The motor should have an overload reset switch. Try moving the motor manually (power plug out) to make sure that it isn't bound up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

My Kenmore canister vacuum (model 11627515700) will not turn on. Although when I set it to CARPET the agitator does come on, however the vacuum still doesn't. Is it likely a motor or switch problem??


Your motor in the canister part of your vacuum is bad you can by a nee one for about $84..They have them used on ebay for $40. just type in Kenmore 116. The reason why your agitator is working is because your agitator has a separate smaller motor. Yo ... Vacuums

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony


... Kenmore Vacuums

I have a kenmore canister vacuum cleaner, 4 yrs. old, model #116.27815701. The powermate assembly, the one for the carpet, seems to have a short or something. The light goes on and off and the motor


... Kenmore Vacuums

Kenmore Canister Vacuum model 116.21514 motor replacement


... Kenmore Vacuums

Kenmore progressive canister vacuum model 116 52612205, I have power and suction but the powerhead motor doesn't come on to run the brushesdo you have a solution


... Vacuums

Motor needs to be replaced - Kenmore 23313 Whispertone Bagged Canister Vacuum


Are you sure its the motor and not a inline fuse or brushes? How did you conclude it's the motor? ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Need to replace motor brushes on Kenmore canister vacuum 116.25914503 - Getting lots of arcing at brush ends. Need tear-down steps to get at the brushes.


If you can see the arcing you are likely in the motor housing. The brushes are specific to the motor depending on RPM. Most brushes and motors in Sears units are supplied by AMTEK Lamb. The color on the plastic housing and stamped model # on motor w ... Vacuums

How do you get the motor out of the housing - Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum


... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

Smoke coming out of my Kenmore Canister Vacuum Model 22550300C


Sounds like a motor err. Could be repaired by a professional but it never be as good as a new one. Also they you might not find anyone to repair it because the replacement motor might cost more than a new vacuum /considering it's age the motor will b ... Kenmore Vacuums

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Looking for Replacement Motor for Bosch Ultra 1450W Canister Vacuum


If you are finding BB's. then the bearings are bad. You could pull the motor and take it to a place that rebuilds motors to see about replacing the bearings. If it is a Lamb or amtec motor, there is a number stamped on it, you can match up another ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0891 seconds