Having problems with your Kenmore Whispertone 23312 Bagged Canister Vacuum ?

The sweeper attachement went "dead." What could be


Answers :

More than likely the overload or reset button has been tripped within the powerhead.
\012
\012Press the red button or the square button on the left side top of the unit, more than likely it is the red one, and it should start up for you again.
\012
\012Good luck,
\012Mark
Repair Help & Product Troubleshooting for Kenmore Whispertone 23312 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The sweeper attachement went "dead." What could be


More than likely the overload or reset button has been tripped within the powerhead. \012\012Press the red button or the square button on the left side top of the unit, more than likely it is the red one, and it should start up for you ag ... Kenmore Whispertone 23312 Bagged Canister Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony


... Kenmore Vacuums

I bout this vacume in mid December 07 and about February-March it started not picking up the dust on the floor. So in early April I bout a new filter and it still wasn't picking up the way it had in the beginning. I've taken it a part several times and cleaned it out with it being plugged at the bottom hose with dust bunnies. Well I just took it back to Walmart where I purchased it and I failed to keep the reciet they could not do any thing about the sweeper. I went back to the sweepers and re


Pull the hose out of the holder, is there suction there. If not, then there is a clog in the hose. If there is suction, then check the dirt outlet by the brush roll. Also if the belt is slipping, it may appear to not have as much suction, belts wi ... Dirt Devil Vacuums

I have a Kenmore canister vacuum - model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** - no air flow. What could be the problem. The cleaner is only 4 years old.


The motor has an inline fuse ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Have Fresh Aire 2.1 about 4 years was running great then went dead. I cant find where the fuse is and have unit apart. I plug in no fan dim display shows to errors. Unit was pretty dirty at the time. I need schematic and suggestions. Also need to knpw how to remove the honeycomb from the light unit to check for blown bulb. Seems brittle and I could break it with trying to pry with augur or sharp screwdiver object.


I'm sorry this may only be a partial help. But fuses are usually very close to the motor, OR where the switch is located. Pretty easy to find by testing but you have to be or so careful you dont electricute yourself. Now if your testing shows v ... Vacuums

My problem is the leak is right where clean water tank sits, its on the bottom where it attaches to machine!!! i went through the booklet for instruction , i found nothing! what could it be?


Dirty, damaged, or missing gasket under tank mounting point. Possible damage at tank under-surface. ... Hoover F5906-900 Upright Steam Vacuum

Loading my 52148 Scunci into the back seat of my truck the connector from the bottom of the handle to the top of the unit snapped off. It appeared to have a pivot ball that went into the sweeping unit to move,turn and pivot the sweeper. I could rig it to sort of function but if the lower handle part is available it would be nice to purchase one, if available. THANX, Don Colo Spgs Colorado


... Scunci 52004 Bagless Canister Vacuum

I have a modelF5914-900 steamvac cleaner.serial #0704 0011 4711 I cleaned the carpets in my house and then started to do the stairs with the stair attachment. I got down to the last four stairs and the solution would no longer come out. I checked the tank and hose connection and tried priming the pump per the instruction manual. nothing worked. Could you make a suggestion as to what the problem could be? Thank You


Check fuses goin to the pump, is the pump working? if so you may have an air pocket or a air leak in the intake. ... Vacuums

Kenmore model 116 27615700 doesn't run with attachments...it only runs with switch on carpet with the carpet attachment. What could be the cause?


... Vacuums

Is there a wrong way to attach the belt and the sweeper?? My Hoover Runabout is making a rubbing noise, like the sweeper is hitting something, and it's real hard to push.


Take off the belt . clean any hair from brush roller make sure movement smooth . re position belt and move by hand to make sure roller is not skew , , rubber is riding sideways and causing friction . ... Hoover Vacuums

I put the flashlight on the charging area and the thing went nuts. I unplugged it and plugged it back in and it went dead.


I think I have bad news for you. It sounds to me like you put the flashlight made out of metal, that conducts electricity across the pins of your cordless vacuum cleaner charger and accidentally short circuited the charger and it went po ... Vacuums

II have the kirby sentria, i have it in canister mode with blower attachment on the hose is on with the hand sprayer attachment the problem is the foam is not coming out the sprayer used it just fine all day went to refill w/ water and cleaner now the foam wont come out whats wrong with it?


Make sure the "straw" is in.See if dust coming out of the hose did not clog the air passages. ... Kirby Heritage II Vacuum

There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?


... Bissell Vacuums

Passat 2000 W Reg Had the rear brakes and disks changed then a month later had a front tyre replaced and as I drove off something went tinkle tinkle on the road (like someone had left a spanner). Week later the ABS light and the brake light come on with the usual STOP Brake Fail Service Manual message. Had brakes checked but they could find no fault. I've tried the ABS under controlled conditions and it works. What could the problem be?? I've been running the car under these conditions and no pr


The ABS module has a history of wearing out on VWs. Nothing wrong with the brakes themselves, but the ABS module would need to be replaced to stop the lights coming on... but the problem is a new ABS module can be very expensive for a new one (~$900 ... Vacuums

We are VERY disappointed in our Steam mop. After only using twice in one year and following all the instructions, went to use it yesterday, Oct. 7th and could not get any steam out? It started up and it felt like it was heated, but no steam therefore could not clean our floors?


Unfortunately they do not work well at all but if it means anything to you your not alone. Many people have complained about the same issue. To be quite honest there really is nothing better than very hot water in a bucket w ... Vacuums

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey


... Vacuums

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

Kirby sweeper shampooer attachment HOW TO use it


 \015\012\015\012Please follw this link to view my carpet shampooing guide. Hope it is helpful!! :0)\015\012\015\012Marci\015\012\015\012 \015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Bissell Quicksteamer I have a Bissell Quicksteamer that is about 5 years old. I went to use it today and hardly any solution was coming out. I could see it suctioning up what little came out, so I took it apart and cleaned it thoroughly. I tried to use again and no solution is coming out. Everything seems to being working just fine. Thanks


Here's a kinda kick yourself quick fix that might be helpful, I took my whole machine apart all the way to the motor to come to realize that the small rubber piece that cover the tip of the water container was jammed in the hole you sli ... Bissell 1770 Quicksteamer II Upright Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad?


My first recomendation would be to try pluging into a diffrent wall outlet as well as something that is on a diffrent circut . It is a known problem that the pins inside that make the connection could be worn out . There are several pins from the one ... Kenmore 21513 Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob


Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

I shampooed my carpet and later that day went to use the Kirby Sentria and it wont turn on... it has always worked fine up to this moment, what could be wrong?


Specifically the bag attachment area. There is a detent on the bag boot that depresses a safety switch. Make sure the bag boot is rotated clockwise into its seated position. ... Kirby Heritage II Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0321 seconds