Having problems with your Kirby G10d Vacuum Cleaners ?

I have a kirby G10D after replacing fan it will not turn easily

\015 When turne on makes a noise and alto motor turns easily when off doesn't seem to be working right when on\015

Answers :

If you mean that you can't turn the shaft by hand then you probably have removed motor to replace the fan. When installing it back you should have tightened screws on the bottom of the unit first and then ones that are inside (with large washers). If this is not the case then we would need more info on what exactly you mean by "not turning easily".
Repair Help & Product Troubleshooting for Kirby G10d Vacuum Cleaners

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kirby G10D after replacing fan it will not turn easily

If you mean that you can't turn the shaft by hand then you probably have removed motor to replace the fan. When installing it back you should have tightened screws on the bottom of the unit first and then ones that are inside (with large washers). If ... Kirby G10d Vacuum Cleaners

Kirby G3 made loud noise when running. Sprayed silicon in fan thinking it might be a bearing. Found a coin and nail in fan and removed. Tha vacuum would not turn on. Replaced switch and brushes. Still nothing. Did the silicon spray do something?

No - the silicon is an insulating material and would have no effect on the electrics of the vacuum. Most likely you have a bad connection - dismantle the vacuum again and check the wiring and the motor with an ohmmeter. Be very attentive with the bru ... Kirby Generation 3 Bagged Upright Vacuum

Trying to replace fan on Kirby g5 but the whole thing keeps turning and I can't get it off, any suggestions?

The threads are left handed on the shaft. opposite than what everyone is used to. there are flat spots on the back of the motor armature where you can put a wrench to hold it from spinning. ... Kirby G5 Bagged Upright Vacuum

Replacing the fan hub on a kirby classic omega 1CB

I resolved the problem .I found a way to hold the armature shaft still while I unscrewed the pulley drive nut ,which must be removed in order to remove the vacuum fan.\015\012\015\012> There probably is a special tool somewhere that w ... Kirby Heritage II Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Fan and bearing replacement on a Kirby G6

If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

Kirby Hello, I have a generation 3 kirby- it was working - I turned it off & it will not turn on again - is there a safety switch /reset button or did the on/off switch go out - I have had it 15 years & replaced the switch 1 time - Thanks

You either need a switch or a cord. Check out my troubleshooting link which includes links to do-it-yourself guides and parts.\015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

Kirby Heritage 2 fan replacement

Take the bag asm. and handle off. Then remove the plastic strip covering the switch, remove the screw there, remove the 3 screws on the housing, turn it over and loosen the screw near the back, the housing should come off. Then remove the screws on ... Kirby Heritage II Vacuum

Replace Kirby legend II fan (impeller blade) - Kirby G4 Bagged Upright Vacuum

In order to replace the fan you will buy a 2 or three piece lexan fan kit containing the fan a spacer and shaft. You must remove the carpet head and then looking from the back of the machine you will find a series of philips screws on the oute ... Kirby G4 Bagged Upright Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us

Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums

Broken fan need a repair man or service centre. If not a replacement fan for self repair. I live on the Gold Coast Ray is my name. Kirby Legend 1 model 2HE

Http://www.ultimatesanitarysupply.com/pdfs/VacuumMaintenance.pdf\015\012\015\012see the link ... Kirby Vacuums

I have a Hampton Bay Midili fan which I just installed about a month ago and it was working fine. A few days ago when I flipped the switch on the light flickered on and off consistently until I turned the switch off. The remote also stopped working to control the fan and light. Since this model only can be controlled by the remote I am worried I will have to replace the remote already after only 1 month!

In many of these remote controlled lamps you cant use the new spiral light bulbs .. you can only use standard incandescent lights .. if thats not the trouble then you may indeed have a bad controller (in the fan) .. there is probably at least a 90 d ... Vacuums

I need to replace the fan blades on a Kirby Heritage II, Model 2HD, vacuum cleaner. How do I remove the drive shaft that the fan is mounted on? Thanks, Robert Croft

... Vacuums

Kirby Lexan Fan is crack and need help to replace

Hello...\015\012Check out my online instructions...\015\012\015\012http://reviews.ebay. ... Kirby G4 Bagged Upright Vacuum

I need to replace the fan and am not sure Kirby G 4 A

Greetings from GoVacuum,\015\012\015\012We've shot a video showing you detailed instructions on how to replace the fan on a Kirby Generation vacuum cleaner. The video is in two parts below. If this video was helpful to you, please be s ... Kirby G4 Bagged Upright Vacuum

I replaced the impeller fan on my Kirby Classic III, it all went back together fine, but there was a leftover piece- the commutator brush cap. Where does it go? Oh, the vac isn't powering up eit

... Vacuums

Replacing the bearing behind fan on a kirby heiritage II 2hd

I don't know what model of Kirby you have but on all Kirby's that I know of you have to remove the fan. Here are two vid's on fan removal for a generation series vacuum. ... Vacuums

Replace fan impeller on Kirby Legend II - Vacuums

Take to repair shop u have have the tools needed to replace ... Vacuums

Dear VacuumRepair, Some months ago, a user reported having a brush on a Eureka4870 that stopped turning easily, even on the highest setting, and after replacing the belt. You indicated that you had an idea, but that it is a lengthy repair, but I'm willing! Can you please advise?

Hi RobertBesides the presence pf some sort of obstruction, the only thing to prevent the brush from spinning jammed bearingsThe bearings sit on each side of the brush. Dirt, dust, hair and carpet fibre can build in the narrow ... Vacuums

Replacing fan assembly on Kirby G2000 - Vacuums

This video should get you half way there:\015\012Kirby belt replacement\015\012\015\012Hope it helps ... Vacuums

The switch on the wall only works to control the fan and not the light- it won't turn off the ligght. I replaced the switch but it did not solve the problem

If this is a new installation and there was only one switch on the wall, say to control a light that was once there, then you have that switch hooked up only to the fan.\015\012If you want to control the light as well, it has to be wired up at the bo ... Vacuums

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.

The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

No manual, want to replace fan Impeller - Kirby G4 Bagged Upright Vacuum

Hi,\015\012 Here is their instructional video....click below\015\012http://www.kirby.com/Portals/0/videos.html\015\012\015\012 He ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1063 seconds