Having problems with your Kirby G4 Bagged Upright Vacuum ?

Kirby shampooer The suds are not coming out of the shampooer. I made sure it was connected right. The sponge filter and the cap are attached. i have a g4 vacuum and the screen in in properly.. if i move at a snails pace i can get spots of suds about every 6 inches or so but not a lot. i have adjusted the on and off, if verified the video its put together correctly but it acts like no suction .. i thought of a small hole in the hose for the suds and cut off about 1 inch it act better but not by


Answers :

On the shampooer tank, remove the screen cap from the little hole that the shampooer hose plugs onto. Clean the screen and make sure that it is not plugged up with debris. Make sure that the screen is securely glued to the cap all the way around the edge. (they sometimes come loose and this will cause the absence of foam) That little (approx. 1 inch diameter) screen is the main ingredient for the foam. The screened cap should fit firmly onto the outside of the little hole in the bottom of the edge of the tank.
\015\012If none of this helps, remove the round sponge and look at the holes in the white plastic circle. Turn the on/off foam valve and make sure that the holes open up when the valve is turned to "on". You can purchase and replace the on/off valve if it turns out to be the problem. You can also buy a replacement tank if you're not inclined to mess with it.
\015\012
\015\012If you need another shampooer manual, check out my guide....
\015\012
\015\012http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTIONS_W0QQugidZ10000000004594992
\015\012
\015\012Hope this helps...
\015\012Marci
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby shampooer The suds are not coming out of the shampooer. I made sure it was connected right. The sponge filter and the cap are attached. i have a g4 vacuum and the screen in in properly.. if i move at a snails pace i can get spots of suds about every 6 inches or so but not a lot. i have adjusted the on and off, if verified the video its put together correctly but it acts like no suction .. i thought of a small hole in the hose for the suds and cut off about 1 inch it act better but not by


On the shampooer tank, remove the screen cap from the little hole that the shampooer hose plugs onto. Clean the screen and make sure that it is not plugged up with debris. Make sure that the screen is securely glued to the cap all the way around the ... Kirby G4 Bagged Upright Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

I have taken this stupid vacuum into the repair and he said I have the belt put on incorrectly. I have watched the video many times and I am putting the stupid thing back together correctly and it will not ****. It does **** with just the hose attachment.


Sounds like a blockage in the base ... Kirby G5 Bagged Upright Vacuum

I have an electrolux epic series 2500 SR that is in pieces and I need to put it back together, I need to get a diagram to make sure it goes together correctly.


... Electrolux Vacuums

Shampooer not delivering suds properly, and its not the suds screen....


I have had this issue numerous times. My husband fnally came up with the perfect solution. He wrapped teflon tape (PTFE tape) around the dumb screen and voila. No more screen coming loose. Mine has always been VERY loose. Infact it would simply fall ... Kirby Ultimate G Bagged Upright Vacuum

Need help putting my bissell carpet shampooer back together


The side that is dragging needs the roller that the brushes are on ,to be precisly pushed back up in it's place,it will take a few minutes and it will not slide back in place easily just use a little force as for the hose diagram, bissell.com,enter m ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Need help putting my bissell carpet shampooer back together


I don't know how to advise you on this. The Bissell is pretty complicated when you take the hood off. Under there is a number of things that must be in place correctly to replace the hood. There is a small plastic "rod" with an "o" ring on it that co ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it


My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How to Install part #KC64EDTEZV06 in the Kenmore canister vacuum cleaner model # 116.22512504 I need a diagram please put pu all the correct wires and parts back together


... Vacuums

Shampooer not putting out suds


There is a sponge right underneath the on/off knob on the shampooer tank. There is a small suds screen right beside it on the small hole that the hose fits onto. Both these things should be cleaned regularly. Here is a pic of the tank..the little bla ... Kirby Ultimate G Bagged Upright Vacuum

Putting back together correctly after installing new heat sensor


The hoover website does NOT give screw sizes,unfortunately!\015\012\015\012cut and paste following info\015\012 ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

How do i put the shampooer together - Vacuums


Http://www.greatvacs.com/shampoo.shtml\015\012\015\012this is a link to a site with step by step instructions on how to use your kirby shampooer... ... Vacuums

After fixing the pull cord on the poulan pro ppb30 /30cc backpack blower i can not get the cord to pull back in if i pull it. how do i get the correct tension on the recoil spring when i put it back together?


... Vacuums

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh


The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How to put my shampooer together? I can't get the water to come out.


... Rainbow Vacuums

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o


It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

I lost the instruction manual and dont know how to put the string in or how to put anything together can u please explain to me how to put the brother xl3750 sewing machine together


Here is a link to your manual:homeappliance.manualsonline.com/manuals/mfg/brother/xl3750.htmlAll you have to do is ... Vacuums

I need to know how to put together a Hoover Slider vaccum. I had to take it apart and now i need to put it back together.


... Hoover S2105 Slider Bagless Stick Vacuum

I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together


Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I own a singer sewing machine model 4562 and tension assembly came unscrewed and now I don't remember how to put the pieces back together. Do yo have a diagram that can be emailed to me so I can put it back together? Thanks


... Vacuums

My daughter pulled to hard on the ceiling fan pulling out the chain. i have taken it off and apart, nothing appears to be broken but im trying to figure out how to put it together so it retracks, i assume it has something to do with the tension of the small spring inside of it, but not sure how to put it back together im wondering if there is a internal diagram of this ???


Don't even bother to repair the pull chain switch, get a new one at KMart, HomeDepot or similar store for less than $2.\012\012Two times I've repaired one, it comes apart when I need it the most.\012\012Good Day! Don't forget to rate thi ... Vacuums

Putting new vacuum together position of the handle


The handle should be attached so that the open portion of the handle is facing towards the brushs( away from user) ... Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum

Shampooer is not sucking up suds into tray


See the diagram and proceed according with the common sense for troubleshooting. God bless you ... Kirby Heritage II Vacuum

Need help putting back together


With out seeing it, it will be hard to figure out what isn't right. Must be a different model then 1699. which model is it? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0332 seconds