Having problems with your Kirby G4 Bagged Upright Vacuum ?

Where do I connect the hose and it's attachments

\015 I lost all my attacments to my G4 and the manuel but have replaced alot of the attacments... Isn't there an adapteer that fits the bottom of the vacuum wheree the brush is to attach the cleaning hose..\015

Answers :

You need the suction/blower connector on the hose:
d42770b.jpg
This must be for G4 or G3 model as later models had this part a bit different.

For rest of the attachment go HERE.
I can sell you used FULL G4 attachment set for 99.00

Good Luck,
Rocky
:-)
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

We replaced the short hose that connects the sucking part to the hole where the dirt goes underneath my Dyson DC07 but now the side of the hose that needs to attach to the machine falls off.


I know the hose you are talking about it is called the DC07 internal hose. Over time the ends can stretch and perish which will mean y ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?


Yes don. call the store where u rented and tell them. ... Vacuums

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live


... Vacuums

The plastic coupler that hooks onto the propane tank cracked. There is a replacement part, coupler, regulator, Y hoses to the main and side burner, avail but how do you disconnect and re connect them? The hoses have a clamped metal ban attaching them to the burner tubes can't get them off. Thermos Barbecue Model # 461410707 Thanks much.


Wrong forum to help you out. ... Vacuums

When running the 2100 Electrolux vacuum, it is stopping and starting when pulling or pushing the floor attachment. Seems like the connection at the top of the handle is a little loose or the electric tabs are loose where the hose connects. Any ideas?


Other option is that on the hose end of the electrical connection, you can use an awl on the electrical connections to bend them in slightly so they make good contact when they are automatically plugged in when you connect the wands. HOWEVER, ONLY D ... Electrolux UltraLux 2000 Bagged Canister Vacuum

New 50 pint frigidaire dehumidifier won't drain via attached hose , only collects water in bucket and this is a pain! How is the hose supposed to be connected? Seems strange to just screw it into the back of the unit; am I missing something?


... Vacuums

Cant figure out how to use the hose attachment,it connects at the top at the duster and at the floor,how do i change it to use the hose only?


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

Where do I connect the hose and it's attachments


You need the suction/blower connector on the hose:This must be for G4 or G3 model as later models had this part a bit different.For rest ... Kirby G4 Bagged Upright Vacuum

How do I hook up the upholstery attachment to a Hooover steam vac. I can find the port for the spray but not the connection for the vacuum hose.


The hand held upholstery attachment does not have a vaccuum, only a sprayer. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Electrolux Guardian Lux 9000 loss of power. I can measure 122 volts to the prongs where the cord is attached but do not measure that voltage at the prongs on the front of the canister where the hose connects. Is the something in the canister that controls the transfer to that plugin?


... Electrolux Centralux Vacuum

Kirby shampooer The suds are not coming out of the shampooer. I made sure it was connected right. The sponge filter and the cap are attached. i have a g4 vacuum and the screen in in properly.. if i move at a snails pace i can get spots of suds about every 6 inches or so but not a lot. i have adjusted the on and off, if verified the video its put together correctly but it acts like no suction .. i thought of a small hole in the hose for the suds and cut off about 1 inch it act better but not by


On the shampooer tank, remove the screen cap from the little hole that the shampooer hose plugs onto. Clean the screen and make sure that it is not plugged up with debris. Make sure that the screen is securely glued to the cap all the way around the ... Kirby G4 Bagged Upright Vacuum

Where do you connect the attachment hose? - Kirby Generation 3 Bagged Upright Vacuum


You have to remove the brushroll nozzle and your attachment hose goes in its place set it on the cross rail, rotate up and lock in place. ... Kirby Generation 3 Bagged Upright Vacuum

I have a Hoover Deluxe Spin Scrub carpet cleaner that has lost suction. I read the solution by Chris Jones of GoVacuum.com, in which he described the design flaw whereby the tool attachment hose tears at the point of connection with the motor housing. That is the case with my machine. Now I just need to know how to repair it. What kind of tape can I use? Plumber's tape? Please help me!!!


A tear in the hose will only affect pick up through the hose when using it to clean furniture, stairs, and such. It will have no effect on the carpet cleaning operation. If the hose cannot be replaced for a while, black electrical tape is one solutio ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do you remove the swivel attachment from the bottom of the hose where it connects to the canister?


... Kenmore Vacuums

I have a modelF5914-900 steamvac cleaner.serial #0704 0011 4711 I cleaned the carpets in my house and then started to do the stairs with the stair attachment. I got down to the last four stairs and the solution would no longer come out. I checked the tank and hose connection and tried priming the pump per the instruction manual. nothing worked. Could you make a suggestion as to what the problem could be? Thank You


Check fuses goin to the pump, is the pump working? if so you may have an air pocket or a air leak in the intake. ... Vacuums

I have cleared the vacuum hose and the attached motor unit. I cannot get the brush going. What else can I do? I have also checked the connections.


Make sure that the belt is on the unit properly not twisted or broken. Also make sure that the brush is set into place correctly and not rubbing on anything else. If both check out fine then the motor is not spinning for some reason and you will need ... Vacuums

My beater bar does not work on my vacuum. The problem is not in the hose or the attachment, because I connected to another electrolux vacuum and it worked. So the problem must be in the canister.


It's most likely a loose wire in the canister then. I recommend taking the whole vacuum to an Aerus Electrolux store and letting the service tech check it out. They can find out the problem quickly.\015\012Be aware they may try to sell you a ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

There is a cut at the end of the hose. Is there a way to cut the hose at the split and reattach it to the connection? Thanks.


Unfortunatly the amswer is no you will have to replace the whole part. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Attachments hose won't **** but blows out


The polarity on the motor mite change with use or low suctoin ... Bissell 3576 CleanView II Bagless Upright Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped


... Electrolux Guardian Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0394 seconds