Having problems with your Kirby G4 Bagged Upright Vacuum ?

I have a Kirby G4. I have noticed the last few days when trying to vacuum that it is blowing more than it is sucking up. I put on a new bag to make sure it wasn't too full. I also put on the hose and noticed it's not sucking as well as normal. I unzipped the back of the bag holder and noticed the bag isn't inflating as it should be as well. I appreciate any advice. Thank you.


Answers :

Take the mini emptor off(plastic piece on bottom of cloth bag) this is done by rotating it away from the body of the machine. There is most likely a clog there. Also take the brush head off and inspect fan for chips or cracks this will also reduce suction. let me know if you need further assistance
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kirby G4. I have noticed the last few days when trying to vacuum that it is blowing more than it is sucking up. I put on a new bag to make sure it wasn't too full. I also put on the hose and noticed it's not sucking as well as normal. I unzipped the back of the bag holder and noticed the bag isn't inflating as it should be as well. I appreciate any advice. Thank you.


Take the mini emptor off(plastic piece on bottom of cloth bag) this is done by rotating it away from the body of the machine. There is most likely a clog there. Also take the brush head off and inspect fan for chips or cracks this will also reduce su ... Kirby G4 Bagged Upright Vacuum

I had a real heck of a time with the bag installation, because after the pop i zipped it up and started to use it and then the bag of the vac, not the replaceable bag fell off and i kept putting it back on but it kept falling off and when i looked inside the bag to reattach it to the vac cleaner i noticed that the dust was all inside. i haven't even used it that much as i keep it to do the upstairs bedroom only. i love that it is so lightweight and easy to use and i hope that someone can co


Mary, I have some wonderful news for you and your Oreck XL2600 Vacuum, I called 1 800 989 3535 customer service and inquired about your bag attach problem, it seems to be a docking station problem that "may" be warranteed, however if it is missing ... Oreck XL2600 Vacuum

My sebo automatic X1 has stopped sucking from the bottom. The hose is sucking well but when I put my hand underneath the bottom part there is no ****. I have cleaned the brushes and cleared the way but to no avail. The bag is only half full so I don't think that is the problem.


... Sebo Automatic X1 Bagged Upright Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate


The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?


After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums

I have a bissell power force vacuum and I just pulled the bag out to change it and when I put it back in it began blowing air out the filter on the side and is no longer sucking


Hello,\015\012Try checking the attachment hose for clogs. It should come completely off of the vacuum with just a few screws. Also, check the little hole underneath the brushroll where the dirt goes in. Hope this helps...\015\012Marci ... Vacuums

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

When removing the canister bag, the plate and spring that it slides into popped out. When I put them back in, the bag full indicator is completely red. It is a new bag and filters. I think I am not getting the plate and spring back in the canister correctly. Any instructions or pictures showing proper insertion and configuration of these? I looked in the manual and the part is only shown while bag being inserted.


... Miele S514 Solaris Bagged Canister Vacuum

The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.


You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing ou ... Kirby G6 Bagged Upright Vacuum

I have the electrolux guardian-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)


Hi,\015\012Check your hose you have something stuck in the hose...stretch it out straight and run something through it to push out whatever is stuck in there...\015\012\015\012heatman101 ... Electrolux Guardian Bagged Canister Vacuum

I have the Aerus Lux7000-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)


Hi, you very likely have a defective control valve under the dial on top of\015\012the vac , or a kink or blockage in the tiny pressure hose that feeds\015\012the air from the throat of the vac or the back of the bag chamber\015\012against the two si ... Electrolux Guardian Bagged Canister Vacuum

I put in a ne Kirby Bag and it still is not sucking up the dirt. The brush is turning but the bag does not seem to be getting any sucking snce it is not expanding


See if this helps:\015\012http://www.goodvac.com/kb_results.asp?ID=13\015\012\015\012Good Luck,\015\012Rocky ... Kirby Ultimate G Bagged Upright Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil


Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you


Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums

I have a BC-A41 vacuum cleaner which has been working well, but now it appears to blow stuff away from the cleaner as I hoover. I find the hose packed up with stuff, but no content in bag. I recently changed the bag...could it be that the bag is not fitted correctly..I am puzzled by the instruction to put the bottom under the rib. I am a pensioner on my own, and would welcome any help. Thanks, Jim


I think there should be some probem in the vacuum section..its failing to **** the objects ... Vacuums

Vacuum cleaner hi.this is 10 yrs old and not overly worked.bags are changed regularly and the micro filter has been changed at least three times over ten years.it goes well for about 2o minutes then loses power with not much "suck"after that.sometimes shutting down completely,because of overheating i presume,or just carries on at a much lower'"suck".have tied shaking bag inside but no luck.any suggestions out there or can you tell me the agents support office for new zealand[auckland].many thank


What brand vacuum is it? ... Vacuums

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?


If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

My floormate is not suctioning very well. Tech support told me to take out the brushes and put them back in and this helped for a little bit then it went back to not suctioning. deb


When you took the brushes out, was there hair wrapped around them? Sometimes they just need to be cleaned off. When you take them off, there is a belt they connect to that also goes around a gear -- make sure the belt and gear don't have hair wrapp ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of


Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

I have a Flotec shallow well FP4122-08. A burglar stood on the pump this summer to gain access to my goats building (window). There's a small black tube that came off at both ends. When I put the tube back on, it shoots right back off as soon as the pump is plugged in. I don't know the name of the part (tube) to order a new one, and I don't know if it just plugs onto the fittings of both ends, or goes into the pump at the end with the round fitting on it.


... Vacuums

Not sucking We have an Oreck XL and today it is blowing out dust instead of sucking it up. I just replaced the belt and about 6 months ago, we took it to our Oreck dealer and had it rehauled. I opened it up to check all and it all looked fine. Then I tuned on the machine while unzipped and noticed that the bad does not inflate as it used to. What can I do? Thanks, Connie [email protected]


You probable have a clog in the handle tube, or at the bottom, either by the brush or in the neck where the handle goes into. Unscrew that big black nut and pull the handle off of the bootom asm, then you can check it out and see where the clog is. ... Vacuums

Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?


... Vacuums

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!


I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0777 seconds