Having problems with your Kirby G4 Bagged Upright Vacuum ?

My Kirby G4 self-propelled wheels stick at times while in Drive?

\015 My vacuum has started to stick at times while in (D) drive. It pulls back OK but seems like it is getting hung up at times when pushing forward. Is this do to a belt? or something else in the self-propelled driver?\015

Answers :

Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kirby G4 self-propelled wheels stick at times while in Drive?

... Kirby G4 Bagged Upright Vacuum

Kirby Ultimate G self propelled drive unit locked up

No, you just need to take it to a shop for repair. ... Kirby Ultimate G Bagged Upright Vacuum

Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.

... Vacuums

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.

The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

Hoover wind tunnel U6425 self propell drive pulley and nut fell off.Now when I try to put it back on and tighten it pulls the clutch assembly over so the accuator is in drive all the time and won'

... Hoover Vacuums

The self propelled feature does not work. Belts are OK but the drive wheels do not seem to be engaging. Is there a cable or something from the lever on the handle that needs to be replaced?

My vacuum cleaner does not turn on \015\012could it be the motor out \015\012i check the switch it ok not getting any power to the switch ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My self-propelled Heritage II Kirby vacuum is no long self-propelled.

Her2 was not self propelled ... Kirby Heritage II Vacuum

Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel

Here is a video how to fix ... Vacuums

Self Propel wheels not enough power to move machine over carpet.

Sounds like the transmission might need an overhaul. Take it to a local vacuum repair shop and have them look at the transmission. ... Vacuums

Kenmore direct drive will no longer self-propell

There may also be a reset button. If the brushes get stuck the unit can shut off power to the brushes to keep a total melt down from occurring. The reset button should return power in these types of vacuums. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Kirby G5 rear wheels lock up completely when in "Drive"

When wheels lock when vacuum is OFF - it is normal. If it happens when Kirby is ON then there are a few things that may have gone wrongPrimary drive belt is broken or something is wrong with plastic gears. See how to check the primary dri ... Kirby G5 Bagged Upright Vacuum

G-4 Kirby self propel unit works in reverse but not foward

Jon,\015\012Here is a helpful link to use to adjust the tranny. About a 7 on the difficulty level.\015\012\015\012http://www.greatva ... Kirby Ultimate G Bagged Upright Vacuum

Kirby g5 self propels too fast - Kirby G5 Bagged Upright Vacuum

The slide has shifted forward slightly, this happens when the kirby\012is hit against walls and skirting boards. you will need a service by your local kirby engineer. see kirby.com for local agent ... Kirby G5 Bagged Upright Vacuum

My Hoover Self Propelled Windtunnel doesn't shut off all the time. Sometimes it is just fine...other times I have to pull the plug. Purchase date8-22-07

... Vacuums

Is the kirby heritage ii self propelled - Kirby Heritage II Vacuum

... Kirby Heritage II Vacuum

Upright self propelled Windtunnel model: The self propulsion does not work and I can see why. I need to know how to get the top cover off the machine to get to the broken part that engages and disengages the wheels. Can you tell me how to get the cover off?

Turn the machine upside down and locate about half a dozen recessed screws which hold the bottom and the top of the machine together. ... Hoover Vacuums

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.

Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

Kirby G5 self propel problem

There is an adjustment for the transmission and it is wrong. It could also be worn. The Kirby has an amazing warranty. See if you can get it serviced for free. ... Kirby G5 Bagged Upright Vacuum


Take the brush belt and slip it over the pull into the groove. Then take the flat belt and hook onto the motor shaft and then pull belt over pull and push it around the entire pulley. It can be difficult but after the first time it is easy. You ha ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Kirby Ultimate G wheels lock up when in drive...

Replace the transmission. The tranny that drives these Kirbys can give you problems. ... Kirby Ultimate G Bagged Upright Vacuum

Hoover Windtunnel bagged self propelled drive not working

Click the link below and watch video how to fixhttp://www.youtube.com/watch?v=K722IsUxjYM ... Hoover Vacuums

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.

Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

I take apart and clean my DC17 every 2 weeks. When I put it back together it always works perfect. This last time, I noticed that the self propel is not working...am I missing something? I took it apart to be sure eveything is in it's place but no difference. Now I have to push really hard.Any suggestions?

The roller is not spinning do to motor or belt not working. If it is the motor then the machine will have to go back to dyson if it is the belt then that is an easy replacement. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0425 seconds