Having problems with your Kirby G4 Bagged Upright Vacuum ?

Fan Replacement How do i get to the fan to replace it?


Answers :

Remove the front piece and there about 4 screws u need to take out and remove that cover, the fan is right there, then u take out the screw that holds the fan blade or impeller as its called out, and put the new on, we just did it. if u have more question, email us at [email protected] for a better explanation.
Http://www.totalvac.com/kirbygen4.html Scroll down towards that middle of the page and you can order a new fan
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no


... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

Fan replacement I have to replace the fan on my g4 how do I get the old fan that is worn and broken off the shaft,,thanks for any help that you might be able to give


Detailed instructions on fan replacement HEREGoodLuck,Rocky:-) ... Kirby G4 Bagged Upright Vacuum

Fan replacement I found the part to replace my broken fan. I've remove many screws, but I can't remove, what seems to be, the obvious plate to get to the broken fan.


Http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMP ... Kirby Ultimate G Bagged Upright Vacuum

Fan Replacement How do i get to the fan to replace it?


Remove the front piece and there about 4 screws u need to take out and remove that cover, the fan is right there, then u take out the screw that holds the fan blade or impeller as its called out, and put the new on, we just did it. if u have more qu ... Kirby G4 Bagged Upright Vacuum

The blue neon light on my harbor breeze fan no longer works. Where can i get a replacement?


It may be the little board that the neon bulb pluggs into. check Ebay for a replacement. Ebay usually has what I need for stuff. ... Vacuums

Trying to replace fan on Kirby g5 but the whole thing keeps turning and I can't get it off, any suggestions?


The threads are left handed on the shaft. opposite than what everyone is used to. there are flat spots on the back of the motor armature where you can put a wrench to hold it from spinning. ... Kirby G5 Bagged Upright Vacuum

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

I put the fAN REMOTE IN the WASHER ON ACCIDenT AND NIW IT WONT WORK WHERE Cn a get a replacement or how can i fix it


Hi,if your lucky enough that no electronic parts get damage inside you can still repair it yourself.Don't put new battery first because it is still wet inside.Open your remote and remove the electronic parts or board ins ... Vacuums

The bottom lamp shade of my fan is broken,model #54wdl, how do i get a replacement


... Vacuums

Fan blade is broken in half on my sanitaire upright I have the replacement but cant get the old one off


... Eureka Sanitaire SC4570 Bagged Upright Vacuum

How do I get the case apart on my Kirby Heritage II (2HD) to replace the fan impeller? I can only find 3 screws holding it and there seems to be more.


From the rear, there are 3 screws on right and one on the lower left. There is 1 more on the front at the top just under the lamp. You will also need to remove the safety switch - the plastic thing down and just right of the front screw. Tak ... Kirby Heritage II Vacuum

Fan and bearing replacement on a Kirby G6


If you run your vac to long after the fan is broke it will cause excessive vibration and the bearings can go out. in almost all cases i replace the fan only. most of the time if you have a bad bearing the vac will make a grinding noise. you can also ... Kirby G6 Bagged Upright Vacuum

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet


Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

Replacing the fan hub on a kirby classic omega 1CB


I resolved the problem .I found a way to hold the armature shaft still while I unscrewed the pulley drive nut ,which must be removed in order to remove the vacuum fan.\015\012\015\012> There probably is a special tool somewhere that w ... Kirby Heritage II Vacuum

Fan replacement gone bad!


I take it the armature is not moving at all when you are turning the pulley(to the right, is right). You may have to pull the motor asm. out, remove the 4 scres and nuts off of the front bearing plate and pull it out along with the armature. I can ... Kirby G4 Bagged Upright Vacuum

Kirby Lexan Fan is crack and need help to replace


Hello...\015\012Check out my online instructions...\015\012\015\012http://reviews.ebay. ... Kirby G4 Bagged Upright Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

FAN PROBLEM??? good morning! my vacuum smells like burnt rubber (fan perhaps) but I can't find how to get into main part of the vacuum. it's just very rounded with no latches or screws to get inside where the motor, belts and fans would be located. can you help me? thank you


There isn't any belts, and the fan wouldn't be rubber, so not sure what you are smelling. Maybe this picture will help you.\015\012\015\012 ... Bissell 6700 Butler Revolution Bagged Canister Vacuum

Replacing the bearing behind fan on a kirby heiritage II 2hd


I don't know what model of Kirby you have but on all Kirby's that I know of you have to remove the fan. Here are two vid's on fan removal for a generation series vacuum. ... Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1


As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

The top of my 500ml/0.6qt thermal vacuum flask is broken and i'm not sure if i can get a replacement as the thermos is still okay. i would be grateful to know if i can get a replacement top so i don't have to buy a new one. Thanks meryl hawkins


Hi there,\012Well yes you can purchase a separate flask for your thermal vacuum, you may purchase them from the dealer or you can please post the brand of your thermos so we can help you to find the part.Good Luck!! ... Vacuums

I have a replacement switch. How do I get the cover off to get at & replace the defective metal switch? Thanx Pete Potter


Hi, you need not to do this yourself, just take it to a electronic repairer around you to take if off and replace the defective metal rather than stress yourself...Take care ... Eureka Sanitaire S661 Bagged Upright Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)


You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0482 seconds