Having problems with your Kirby G4 Bagged Upright Vacuum ?
How do you replace the belt on a G4 Kirby Vacuum?
Remove the head from the machine, and unlatch and remove the bottom plate. The brushroll can now be pulled or pryed out. Slide the new belt onto the brushroll and center it. When re-installing the brush, note that one end cap is wider than the other. The brush caps are also marked with 1, 2, or 3 notches to adjust for wear. In normal use, setting 1 should face the carpet. Be SURE both ends are on the same setting. Replace the metal rug plate and turn the belt lifter counterclockwise to stretch the belt into a loop. Place the head back on the machine, latch it firmly in place, and turn the belt lifter clckwise to drop the belt onto the motor shaft.
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP
Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum
I need to replace the belt on my kirby. - Kirby Ultimate G Bagged Upright Vacuum
If this is like my Kirby, there are colored slots on each end that slides the brush in and out and they are different sizes but the belt is connected in the middle. First take the bottom cover off. It should be made out of rubber and metal, and it po ... Kirby Ultimate G Bagged Upright Vacuum
Son took the front plate off the kirby heritage II vacuum thinking that was how to replace the belt, now don't know how to put the three rings and belt catcher back on?
Looked at a kirby vacuum that a family member has and saw how it was assembled! Thank You ... Kirby Heritage II Vacuum
How do you replace belt on a Kirby G5 - Kirby G5 Bagged Upright Vacuum
Hi there SmartAlec from NelsonVacuums.com.au here. I was going to write an explaination on how to do it when i cam across this great video clip of how to do it on youtube. ... Kirby G5 Bagged Upright Vacuum
I need to replace my belt on my kirby g4 - Kirby G4 Bagged Upright Vacuum
Hello, amhillI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ... Kirby G4 Bagged Upright Vacuum
Instructions to replace the belt on my Kirby Dual Sanitronic 50 vacuum. this is the belt that drives the brush.
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
Replace the belt - Kirby G4 Bagged Upright Vacuum
Click on the link below for instructionshttp://www.youtube.com/watch?v=At7tqnjD-Kc ... Kirby G4 Bagged Upright Vacuum
How do you replace the belt on a G4 Kirby Vacuum?
Remove the head from the machine, and unlatch and remove the bottom plate. The brushroll can now be pulled or pryed out. Slide the new belt onto the brushroll and center it. When re-installing the brush, note that one end cap is wider than the other. ... Kirby G4 Bagged Upright Vacuum
Govacuum kirby belt replacement - Vacuums
How do i replace the belt - Kirby G6 Bagged Upright Vacuum
Hello,Check this out, it should help:http://www.goodvac.com/articles.asp?id=143Good luck,Rocky ... Kirby G6 Bagged Upright Vacuum
Replace carpet cleaner belt - Kirby Heritage II Vacuum
... Kirby Heritage II Vacuum
Kirby G4 How do I replace the belt on this vacuum....
Take off the noozle, take off the bottom plate and remove the brush roll and old belt. Check the brush roll while you have it off to make sure the end spin freely. Put the belt on the brus roll and re-install in the noozle, put on the bottom plate. ... Windsor SR12 Sensor Bagged Upright Vacuum
How do you replace belt on kirby vacuum cleaner
Try removing the screws under the vacuum by the rotating brush assembly. Remove the cover, loosen the brush to remove the belt and reassemble in reverse. ... Kirby Vacuums
I need topknow how to replace the belt - Kirby G4 Bagged Upright Vacuum
The following link lead to the Kirby site, which has an excellent instruction video for replacing the belt. Just click on one of the symbols to the right of "Changing the Belt". If you don't have either of these video viewers, you can download one at ... Kirby G4 Bagged Upright Vacuum
How do you replace belt on kirby g series? - Vacuums
Hi,1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off) \015\0122)Remove the power head from the front of the machine. Now turn\015\012the belt lifter the other way and li ... Vacuums
How do you replace the belt on my Kirby G5 vacuum cleaner?
Hi There,We've created a great video demonstration on how to replace the belt on Kirby generation vacuum cleaners. This will walk you through step by step on how you can replace the vacuum's belt, as well as do the basic maintenance on ... Kirby G5 Bagged Upright Vacuum
How do I replace belt on 2001 G kirby vacuum cleaner ?????
... Kirby Ultimate G Bagged Upright Vacuum
How do I replace the drive belt on a Kirby G5 vacuum cleaner?
Greetings,I have shot an excellent video repair on how to replace the belt on Kirby Generation Vacuum Cleaners including your Generation 5 (G5). The belt change procedure is the same for Kirby Models G3-G10 Sentria. The video is below in ... Kirby G5 Bagged Upright Vacuum
Trying to replace a broken belt - Kirby Vacuums
Here is the link to the detailed instructions for belt changing. When you take the brushroll out, make sure that the brushroll spins freely. If it doesn't it will burn up your belts and needs to be replaced. ... Kirby Vacuums
I just replaced the belt on my Kirby Heritage II, and it keeps coming off. It is engaged when I check it, but as soon as I start vacuuming, it comes off?!
You got the wrong size. ... Kirby Heritage II Vacuum
Not sucking i have a KIRBY G3 that was working great. One day there was a strong smell and the brush roller belt broke so I replaced it. The fan looks good. Now the vacuum does not **** up dirt but instead seems to very gently blow air forward. I took the (new) bag off and it is blowing hard int the bag. I am stumped!
Belt is not connect to the drive pulley, see manual for fitting or see utube for video ... Kirby Generation 3 Bagged Upright Vacuum
I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums