Having problems with your Kirby G4 Bagged Upright Vacuum ?

G4 kirby My unit just stoped *I think it's the fuse and I don't know where it is HELP!


Answers :

Ensure the safety switches are made properly by making sure the front brush assembly is fitted properly, you will see a tag that enters the machine making the front switch, secondly make sure the bag bottom housing is on properly and fully rotated so that its tag makes the switch on the side.
\015\012The only fuse is in the plug (UK).
\015\012Common fault is the mains lead broken internally, unplug from the side of the machine after removing the little cover where the wire goes in. You can use a kettle lead to test the hoover.
\015\012If this does not cure it most likely the motor brushes are worn.
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

G4 kirby My unit just stoped *I think it's the fuse and I don't know where it is HELP!


Try my troubleshooting guide...\015\012\015\012http://reviews.ebay.com/COMMON-PROBLEMS-WITH ... Kirby G4 Bagged Upright Vacuum

Sponge filter I have a kirby sponge filter for my Sentria shampoo system and dont know where it goes. It stop working and making foam. Kirby sent me the sponge filter saying this is what i need and i would know where it goes. I dont nor kind I figure it out. please help!!!!!!!


On the end of the shampoo tank where it attaches to back of motor where the bag is normally attached ... Vacuums

Hello, Could you send me an exploded view of an engine kirby please? My Kirby vacuum cleaner I think for 1997 I think it is garnet, having wanted to change the coals, I do not know the back, is the cause of my request, I contacted a person previously in Bastogne (Belgium) several times which promised to help me but in vain, I count on your good will so I can reassemble it and use it again. In advance, thank you


Try this site out:www.onlinevacshop.com/kirby-G5-parts-manual.phpGood Luck!Jim ... Kirby G5 Bagged Upright Vacuum

Kirby G3 I threw out my last bag for my kirby. I have an other model and now i dont know which type I need to get. I have 4 Style #2 bags but they are not the right ones... Help!


Beginning with the G series, G3 and G4 had round openings for the dirt intake. Prior models had oval so they will not fit, so find G3 or G4 bags and you will be set ... Kirby Generation 3 Bagged Upright Vacuum

My daughters X-Treme Scooters | X-360 - 350 Watt Electric Scooter - Pink the fuse keeps breaking or blowing in it. Do you know what could be causeing that? Please help she really loves her scooter and we dont have a clue nor a manual to see what is wrong with it. It will run until she pushes the gas all the way and it gets hot.


Hi, be sure you are using the right amperage fuse in it. Check any exposed wires on it they may have got skinned up, causing a short and blowing this fuse. You say it gets hot when she gives it full power, so its blowing when its drawing the most amp ... Vacuums

I want to take apart a kone dirt devil and i know how it has to be done but i dont have 5 hands to do it. there has to be a tool that presses on the four sides of the case so you can slide the motor unit out. can you help me with this


... Dirt Devil KONE Cordless Hand Vacuum Vacuum

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'


Machine will not come on ... Kirby G6 Bagged Upright Vacuum

Dont know how to put the shampoo system together on my kirby g6..


Http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTIONS_W0QQugidZ1000000000459499 ... Kirby G6 Bagged Upright Vacuum

I just got this euro pro shark steam mop. I dont have a manual for it so i dont know much about it. I put water in it and it heats up but when you start to use it. It makes a gurgling kind of sound and steam comes out, but not very much i dont think and on the floor you can't hardly tell where you went over the floor at cuz it's not very wet at all. So is it suppose to make a gurgling sound and should'nt the floor be alittle wetter?


Call Shark. They have good cust. support. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo


The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I have a Bernina 930 sewing machine. I read the advice from "dogdanes" about the basting unit seizing up and I think this is my problem. It has happened once before, and I NEVER use the thing, so I think it's frozen. My flywheel won't turn. Can you help me fix this? I have a sewing business and can't afford to have my Bernie in the shop for weeks. Thanks. Maripat


Hi marjpatv,With your Bernina 930 sewing machine where the flywheel won't turn and seems like it's frozen, sounds like it needs some oiling. You may want to try having it oiled first since it could be a possible cause of this issue. You m ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

I have a fake nokia n8 cell phone(basically called chinese). i didnt know about flight mode and turned it on by mistake. now i dont know how to turn it off. menu is not opening and i cant make a cal... plz help me out.. :(


Take the power button should give you the option to turn off airplane mode ... Vacuums

Hi. I have a Kirby from back in the early 90s (model G3D). Never had major issues with it. Can't remember the last time I had maintenance/tune up done. It's just sounding different when I run it the last few times...almost like it's louder and kind of echo-ey. Still suctioning well, but something's not right and I don't want to run it until I know if anything's up. Any suggestions? I'd like to try and figure this one out on my own with your help. Thanks in advance for your help. Marci


Check the belt. this is a strong vaccume and even without the belt it will still have a decent amount of suction. If the belt is not tight or intact it can let the motor turn faster which will sound louder. other than that check all the hoses for hol ... Kirby Ultimate G Bagged Upright Vacuum

I have a kirby 2000 g limited edition, and I am looking for a hose that will fit it. Do you know the part number by any chance or another Kirby hose that is interchangeable? Any help will be appereciated. Thank You, Lori


... Kirby Vacuums

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

I have a Eureka Altima vacuum. The model number is 2996. I don't think my vacumm is sucking any dust. Plus, it smells like a burning leather. What should I do? I have tried to get help from others and they tell me that I should change the belt. But, I don't know where it is. Please help.


Sounds like the belt for sure. Here is a link with the owners manual. It shows how to get to and change the belt. http://www.eureka.com/index.php?option=com_productdisplay&view=productdisplay&task=getproducts&productid=2&produ ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I just bought a 2nd hand Kirby & not really know how to start. it didn't come with any operation Manual or CD. I realized its a re-po set. I think its Kirby Ultimate G Bagged Upright Vacuum, as there is nothing to identify it.


Here's a free guide for the shampoo system and I have both book and DVD manuals available for purchase. Hope i've helped...\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

I have the scunci 1000 steamer- it was sitting for a while and the cap on the top looks like its corroded and i cannot remove it from the steamer - i just bought it a year ago, but i think the salt or vinegar from cleaning it got trapped in the top and i tried everything i could think of to loosen the top so i could pour water into the unit and use it again; otherwise it is in perfect condition, but i tried even pliers and i cannot loosen it and i dont want to break it, but am so frustrated - wh


Hi, Elaine, W/D here.Corroded items are difficult to break loose as the corrosion builds up a layer that binds the parts together. Try this, as I usually have good luck with this method:Tap around the perimeter of the cap with a wooden h ... Scunci SS1000 Handheld Steam Cleaner

Sylvania microwave oven model # SM81012. The unit turns on, timer counts down, etc, but the unit does not heat the food. I think there's a problem with the way the door latch catches. But I don't know if/how I can access it.


... Vacuums

I need to know how to change my kirby into a blower?


Raise the light assessory on the front of the vac. Remove the roller assembly by rotating the square dial as indicated by the arrows. Then you must attach the accessory that sort of looks like a 4 inch square open box to the front of the vac where ... Kirby G4 Bagged Upright Vacuum

My eureka Hello im not sure what kinda of eureka it is a friend gave it to us...and I went to change the bag and vacuum and the spinner isnt going...and i dont think its the belt...help please! i looked on the back and it gave me a modle number its 4475


The belt may look ok, but am sure it is stretched and when this happens, the brush roll won't turn like it should. Did you check the brush roll ends to see if they turn freely, if not replace it. ... Vacuums

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

Son took the front plate off the kirby heritage II vacuum thinking that was how to replace the belt, now don't know how to put the three rings and belt catcher back on?


Looked at a kirby vacuum that a family member has and saw how it was assembled! Thank You ... Kirby Heritage II Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0850 seconds