Having problems with your Kirby G4 Bagged Upright Vacuum ?

G4 plug i'm trying to replace the plug just don't kow which wire is which? can u please help


Answers :

Brown wire to fuse (Live), blue wire to left pin (Neutral), Green and Yellow wire (If fitted) to top pin (earth).
Does not matter much. Any will do.
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

G4 plug i'm trying to replace the plug just don't kow which wire is which? can u please help


Brown wire to fuse (Live), blue wire to left pin (Neutral), Green and Yellow wire (If fitted) to top pin (earth). ... Kirby G4 Bagged Upright Vacuum

Have a Genie 2020L garage door opener. Door start to go down then stop and return. Tried cleaner old sensors. Same. Noticed red light on sensor 3blinks then off....repeat constantly. Replaced sensors - same issue. Reset unit...checked all wiring...no jams anywhere.... HELP PLEASE L:-)


... Vacuums

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin


Check the cord to make sure you have continunity throw both leads, check them at the cord reel, there are 2 wires hooked up to it, if not then the cord is bad. Check the swith also, the next cause would be the speen control mounted on the motor, par ... Miele Cat & Dog 326i Bagged Canister Vacuum

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin


Hello, First check the cord to make sure you have continunity throw both leads, check\015\012them at the cord reel, there are 2 wires hooked up to it, if not then\015\012the cord is bad. Check the swith also, the next cause would be the\015\0 ... Miele Cat & Dog 326i Bagged Canister Vacuum

Hello, I,ve just bought an Italian designed 3 bulb 70's wall lamp. It has a 2 wire lead feeding out with 2 wire lead running from one bulb socket To the other 2 inside the casing. I'm trying to wire it in my porch which has 3 wire cable coming from a 13amp plug for power. Any suggestions on making this work please ?


... Vacuums

Wiring Schematic I need the wiring schematics for my XL3600HH, as I am replacing the motor and did not receive the schematics. Unfortunately, I can not remember the exact wiring. Please help. Thank you


Hope this will help you. There is 4 different ways to hook it up depending on what you have,\015\012\015\012 ... Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

I recently purchased a Sunbeam Artista EM5900 model coffee machine. I plugged it in and pressed the 'Power' button only to find the power go out. I understand this is short circuiting, so I went and turned the power back on. I then moved the machine to a different powerpoint and plugged it in - the same problem happened and I have tried it countless times on various other powerpoints. Help please?


Try it in a different part of the house. If it works then you have too many things running in the kitchen.\015\012If it still blows a breaker then it is shorted out and needs to be returned. ... Vacuums

TRYING TO REPLACE THE PLUG ON An ELECTROLUX Z5915 1600W vacuum cleaner, IT HAS TWO WIRES from the cord.....BROWN AND BLUE.....BUT 3 POSSIBLE CONNECTIONS ON THE PLUG NOTED N, L and the earth connection.


... Electrolux Vacuums

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I've recently bought a hitachi HDR505 & haven't had a problem using it with an indoor ariel other than the fact in bad weather conditions there have been problems with the signals. So I tried to attach the ariel wire that connects from a box in the corner of my living room which connects to the outdoor ariel but cannot connect it into the 'ariel in' compartment on the box as it does not fit into that hole but does fit into the 'ariel out' hole. Please could I get help with a solution asap as I w


... Hitachi Vacuums

I'm trying to replace the belt that drives the sprayer on my Bissell ProHeat but the package with the belts did not come with instructions. I keep finding instructions on the internet, but without pictures, I have no idea what I'm supposed to do. Please help.


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I took the battery out over winter and am now trying to put it back in, but can't remember how to hook the wires back to it. Please help me! Best Regards, Natalie L.


+ is red wire positive hookup. -- is black wire or negative hookup. the symbols are by the battery posts on top of battery. have a good one !! ... Vacuums

I am trying to get replacement parts for the shark ultra steamer, cannot find anywhere. Can anyone please help. Thank you


You can start with this URL\015\012\015\012http://www.vacsewcenter.com/browser.asp?AdvSearch=Shark&gclid=CKrXi5bEyaQCFQf3iAodyVcpEw\015\012\015\012Paul ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I'm trying to remove the power switch assembly for my Dyson DC25 so I can replace the power cable. I took out the 3 screws with a T15 screwdriver and released the top two retainter pins, but the lower half of the assmbly won't detach. Please help!


Replace the two bottom screws but don't tighten up just a few turns in will do, then using the screwdriver push firmly each screw and this will release the lower part of the cover hope this helps. ... Vacuums

BOSCH ERGOMAXX MODEL BSG82000GB/01 BAGGED VACUUM CLEANER NOT WORKING AFTER VACUUMING MY CAR, CHECKED FUSE IN PLUG AND CABLE WIRES ALL OK, I SUSPECT THE MOTOR HAS OVERHEATED BUT THE MACHINE JUST WENT DEAD JUST AS IF YOU PRESSED THE OFF BUTTON, NO SMOKE OR BURNING SMELLS??? PLEASE CAN ANYONE HELP.


... Bosch Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Every time we plug in the vaccum hose into the wall recepticle the vaacuum turns on for half a second and then blows the circuit breaker. This just started a few days ago. We tried replacing the 20 am


... Dirt Devil CV950 Central System Vacuum

Need to replace power cord on Hoover windtunnel need wiring help


Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

I have a Janome Model 556, purchased in 1968 in Zimbabwe. I need to know how to replace the wires of the foot pedal. There were 4 wires used to go into the small plug attached to the machine, however the wall plug only had 3 wires.


... Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available


Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1


As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Hi, I have an old 2 wire chandelier I would like to make a plug-in. I have bought the wire swag kit to change it, but the chandelier wires are unmarked. Both wires are copper and I cannot see an insulator on either side...I need help!! Thanks!


Can you determine some way of telling which wire goes to the center conductor on each of the lamp sockets. (That particular wire,-- however it is identified-- (Maybe a tracer thread? in the woven ins ... Vacuums

I love my Keurig.....I have recommended it to many of my friends...3 of my friends asked if they could use their own coffee (and not trying it I said yes)...I have been told that the coffee grinds come out and are in the machine. I thought maybe they used too much coffee (but they tried various amounts)so I tried it myself and sure enough the grounds were all over the place. Even if I half filled the container....PLEASE HELP as they are cursing me...


Dont try it ... you will cause lots of troubles. Ops, you already tried it ... There is a special filter in the cartridges. I dont think you can replicate the cartridge.\015\012\015\012Thanks for visiting today. ... Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0749 seconds