Having problems with your Kirby G4 Bagged Upright Vacuum ?

Kirby G4 Toe-Touch Control pedal jammed

\015 The pedal is jammed in the "down" position and won't raise the front of the Kirby.\015\012\015\012\015\012\015

Answers :

Flip the Kirby over,and you will find screws that hold the front axle in place.Remove the screws and the front axle.Debris may be caught in the mechanism.Clean the debris out,and use WD-40 to lubricate the mechanism.May be able to do this without removing the axle,but removing it allows for better cleaning or for identifying broken or missing parts.
Repair Help & Product Troubleshooting for Kirby G4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby G4 Toe-Touch Control pedal jammed

Flip the Kirby over,and you will find screws that hold the front axle in place.Remove the screws and the front axle.Debris may be caught in the mechanism.Clean the debris out,and use WD-40 to lubricate the mechanism.May be able to do this without rem ... Kirby G4 Bagged Upright Vacuum

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

The toe- touch control and wheel has fallen off my kirbyG6

I believe you are talking about the pedal that selects powerdrive. That shaft end is stamped on in manufacturing. If you take it apart you'll see where it is to hold the shaft in place. When we see them it normally requires a used transmission. There ... Kirby G6 Bagged Upright Vacuum

Kirby 3g I have a kirby 3g about 4 yrs old and when I push it forward it just takes off, how and I adjust the tranny to control it better. Jeff

\015\012 Here's a link on how to adjust the transmission on the kirby...the kirby pictured is a G4 or 5 but it is the same transmission as the G3\015\012\015\012\015\012 \015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

The suction mode only pedal spring might have come loose. is there a diagram to help me fix it? its a hoover windtunnel t series uh70200. the pedal doesnt click into place after i forced it down when it was jammed.

... Vacuums

My Sentria always runs in the drive mode and it is so fast it seems out of control. If I push the neutral pedal it stays in drive. I can push it the regular way when it is turned off, whether the pedal is in the drive position or neutral.

I sold vacuums for almost 20 yrs and the Kirby gets lots of complaints. The transmission that it has in it breaks as your has and they are costly.The best thing to do would be to take the maching to the local vacuum store(eg. sewing and vacuum are of ... Kirby Ultimate G Bagged Upright Vacuum

Kirby G7D neutral drive pedal

... Kirby Ultimate G Bagged Upright Vacuum

Kirby G5 Techdrive pedal

Kirby N/D pedal is an assembly that can not just come out. So I would say that it is most likely broken. See THIS ITEM and if the ... Kirby G5 Bagged Upright Vacuum

The suction mode only pedal on my windtunnel series t model uh70200 got jammed

... Vacuums

Kirby neutral/drive pedal

HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

Singer 4526C appears to be jammed. Hand wheel very stiff to turn and when pressing foot control machine moves very slowly.

... Vacuums

KitchenAid slide out Exaust fan Mod# KWVU265YBA-O Would not work (lite,fan) every once in awhile, now quit working all together.Could it be the micro board or is it the touch button control?

I would first start out by cleaning the touch pad from all the oily smoke residue over time,these membranes get dirty and the smoke residue insulates the connections on the switches and back side of board,then if possible bypass the module and see if ... Vacuums

My G6 kirby stopped working. i have checked the wire for fraying and continuity and found no problems. I have noticed that the foot pedal that turns the machine on doesn't seem to click when pushed on or off either. i have the motor exposed now to check if it is bad, but i am not sure how to pursue doing just that.

... Kirby G6 Bagged Upright Vacuum

Kirby sentria neutral drive pedal fell out - Vacuums

... Vacuums

Our Bissell ProHeat carpet cleaner is not working. The power is connected because the red heat lamp is on, however when you touch the foot pedal for the start of the rollers, the power is not connecting. Short somewhere??? How to locate the short? Please advise. Thank you.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Hi, I bought a Homedics toe touch weighing scale about 12 months ago (or less). I don't use it that often but a short time after I'd bought it it has started give inaccurate readings in terms of weight or no weight readings at all and just gives me the 'Err' message. I have changed the batteries but this doesn't seem to help neither does using it on a hard surface. Any ideas - I haven't kept the receipt so can't take it back! Regards Eleanor Kirk

... Homedics Vacuums

Have a kirby vacuum and it names a place to turn the shampoo tank off and a place for the suds control valve where are these two things when i am shampooing

Hello, saI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I w ... Kirby G4 Bagged Upright Vacuum

Have oiled my Bernina 707 minimatic 1970 sewing machine and I have power when I press the foot pedal, but when the handwheel is tensioned none of the mechanism under the free arm cover plate moves. I went to sew something and the needle jammed. I took the covers off and there is no debris - it was all oiled and left overnight. Now the Take up lever doesn't move and is in the down position.

... Vacuums

I've owned my Kirby G4 for 15 years and never had to touch it for maintenance. Should I ever get it overhauled or tuned up?

You can find a lot of useful information on how to service your Kirby on our website:http://www.goodvac.com/ look at ... Kirby G4 Bagged Upright Vacuum

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

My Kirby G6 Techdrive pedal came out of the machine. I do not see how to secure it in the unit so it will engage and disengage the drive. Any guidance? Did something break or come off of the shaft?

\015\012The Kirby Gsix is equipped with TechDrive Power Assistant. This feature makes it very easy to move your vacuum back and forth, eliminating any effort on your part. The KirbyTechDrive pedal is opera ... Kirby G6 Bagged Upright Vacuum

How do i put the drive pedal back on a kirby ultimate G vacuum?

... Vacuums

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?

Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

KIRBY G6 Wheel with the foot pedal to raise and lower has fallen off and wont seem to go back on????

... Kirby G6 Bagged Upright Vacuum

To to put together the neutral drive pedal of kirby sentria

... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0328 seconds