Having problems with your Kirby G5 Bagged Upright Vacuum ?

Can't seem to pick up small items like lemon pips with Kirby G5. It just runs over them or pushes them backwards and forwards.

Answers :

It sounds like your belt is broken, OR your beater bar is rotating but has not been adjusted downward to reach the carpet pile. Check by running the vacuum and looking to see if the beater is moving.
Repair Help & Product Troubleshooting for Kirby G5 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't seem to pick up small items like lemon pips with Kirby G5. It just runs over them or pushes them backwards and forwards.

It sounds like your belt is broken, OR your beater bar is rotating but has not been adjusted downward to reach the carpet pile. Check by running the vacuum and looking to see if the beater is moving. ... Kirby G5 Bagged Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.

The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

I had to replace the switch in my Kirby G6. It took some doing but I got in out and the new one in. I must have miss labeled the wires because when I pull backwards the clutch pushes forward. Ther

Go to kirbvacuums.com and look up your model number ,they might even have a toll free number you can call ... Kirby G6 Bagged Upright Vacuum

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.

Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

My kirby vaccum has tech drive and it is stuck in reverse. The wheels spin backwards up lock up when I push it forward

... Kirby Ultimate G Bagged Upright Vacuum

In drive I can push kirby forward but not backwards

It will be the transmission this video will help you ... Kirby G5 Bagged Upright Vacuum

Brush won't rotate when pushed forward

I had the same problem . The reason it acts like that is due to the cable that runs from the vacuum motor to the brush assembly has an intermittent open. My fix was to find the small cable that was causing my troubles and splice it. Making sure that ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks

I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hoover Elite motor runs when moving backwards but not forward

Are you sure its not just your belt on the beater of head slipping and needs to be replaced? ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900

Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

It runs mostly backwards, and in circles and will push itself up

Make sure you have the battery in correctly plus to plus and minus to minus ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.

Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

My e series rainbow has stopped picking up and the dust gathers on the top of the nozzle. It will pick up a little when I push it forward, but when I pull it back dirt and debris comes out of the noz

<p>Did you recently remove the brush roll? If you installed the brush roll in backwards, then this can happen. You can <a rel='nofollow' href="http://www.rainvac.com/rainbow-vacuum-manuals">download the manual </a>on how to replace ... Rainbow E series Canister Wet/Dry Vacuum

My Kirby Ultimate G does not have enough suction to pick up pet hair. Is there anyway this can be corrected? I felt under the vacuum when it was running, the roller is running, but I felt very little suction.

An Ultimate G has lots of suction. If you turn on your vacuum and the bag immediately inflates - that is how you can tell if your Kirby is moving air (suction). There is a more modern brush that came out with the Ultimate G Diamond and the Sentria ... Kirby Ultimate G Bagged Upright Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.

You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

I have a Dirt Devil Vision self-propelled vacuum cleaner. Recently, the self-propelled feature is stuck in the backward mode, so it only goes backwards! I can get it to go forward if I push really hard (i guess it is good for a workout!). I try to turn off the propel feature completely, but it will not turn off. please help!

Hi, the problem you are having is going to be with the switch that controls the forwards and backwards settings so with this stuck in backwards their is no way you can get this turned off, the other problem is your not going to be able to replace thi ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?

Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums

New Kirby I own the new Kirby Ultimate Diamond Edition..G Series and the brushes are running OK and everything but it seems to be blowing things out and not picking them up. Can you help me. My serial number if 7051201028

Is the bag emptor all of the way on? It will blow out if it isn't, But being new, you must have a number to call, it is under warranty so they should be able to help you out. ... Kirby G5 Bagged Upright Vacuum

Hello, I got a used Kirby Sentria. When I run the vaccum and push and pull on the handle, I can hearing a friction type noise. I got up close to the vaccum and it is not the wheels or roller. It is coming from the base of the handle. It's like it is pushing on something on the vaccum body and is creating the noise. Maybe transmission? Is this normal, or is it something I should be concerned about? Thanks for your help!

Try new belt yours may be slipping ... Kirby G5 Bagged Upright Vacuum

Kirby 3g I have a kirby 3g about 4 yrs old and when I push it forward it just takes off, how and I adjust the tranny to control it better. Jeff

\015\012 Here's a link on how to adjust the transmission on the kirby...the kirby pictured is a G4 or 5 but it is the same transmission as the G3\015\012\015\012\015\012 \015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

Kirby G5 pulls to the right and sutters when pushing forward

First adjust the height of your brush. You will have to take the bottom plate off as you were changing a belt. There are 3 height adjustment settings located at the end caps marked 1,2, and 3. Take note of where it's at and ... Kirby G5 Bagged Upright Vacuum

Two weeks ago, my 4150 roomba stopped during running and sounds "ehh". every time i hit the clean button it sounds "ehh" and doe'snt work. at the first time it did it ,i have cleaned the sensors then it start moving forward and backward until it stopped . from now on it only sounds "ehh".

EHH sound:-------\015\012Cliff sensors are dirty or need repair.Try cleaning the sensors and check.If still the same problem then the sensors needs to be rechecked and its connections has to be replaced.\015\012You can try this opt ... iRobot 4150 Roomba Vacuum

My dyson ball vac bounces when I pull it backwards. It works fine when I push it forward.

They bounce because they spin backwards try to pull back slower. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Want stay running after pushing on button - Kirby Ultimate G Bagged Upright Vacuum

I'd say it's either the cord or the power switch with the switch being my first guess. Here's my free online guide for the do-it-youself repairman...\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Hoover U8185-900 motor shuts off when you move the cleaner forwards but it runs when the cleaner is moved backwards

... Hoover U8185-900 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0626 seconds