Having problems with your Kirby G5 Bagged Upright Vacuum ?

Kirby G5 pulls to the right and sutters when pushing forward

\015 Pulls to the right and sutters when pushing forward. Does anyone know what parts I need to replace?\015

Answers :

First adjust the height of your brush. You will have to take the bottom plate off as you were changing a belt. There are 3 height adjustment settings located at the end caps marked 1,2, and 3. Take note of where it's at and try the other two to see what works best. If that does not work, go to your local Authorized Kirby dealer and have them install the softer brushed. Often this is required for berber carpet.
Adjust the height of your brush.
Repair Help & Product Troubleshooting for Kirby G5 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby G5 pulls to the right and sutters when pushing forward

First adjust the height of your brush. You will have to take the bottom plate off as you were changing a belt. There are 3 height adjustment settings located at the end caps marked 1,2, and 3. Take note of where it's at and ... Kirby G5 Bagged Upright Vacuum

I had to replace the switch in my Kirby G6. It took some doing but I got in out and the new one in. I must have miss labeled the wires because when I pull backwards the clutch pushes forward. Ther

Go to kirbvacuums.com and look up your model number ,they might even have a toll free number you can call ... Kirby G6 Bagged Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.

The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

Hoover Savvy The red light for the dirt finder is on when pushing forward and the green light is on when pulling it back. This happens all the time. It's like the dirt finder sensor isn't working right. It seems to be picking up good and we keep the filter clean.

Does this happen at both Dirt Finder Sensitivity settings? ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'

Machine will not come on ... Kirby G6 Bagged Upright Vacuum

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks

I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900

Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Kirby 3g I have a kirby 3g about 4 yrs old and when I push it forward it just takes off, how and I adjust the tranny to control it better. Jeff

\015\012 Here's a link on how to adjust the transmission on the kirby...the kirby pictured is a G4 or 5 but it is the same transmission as the G3\015\012\015\012\015\012 \015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.

Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

Greetings - my Dyson DC41 animal vacuum seems to be having problems with the ball - the right side of the ball if you were to be standing behind the machine seems like it's tightening as it rolls forward, as it tightens its harder to push the machine forward. Any thoughts, any fix it ideas? Thank you.

... Vacuums

Hello, I got a used Kirby Sentria. When I run the vaccum and push and pull on the handle, I can hearing a friction type noise. I got up close to the vaccum and it is not the wheels or roller. It is coming from the base of the handle. It's like it is pushing on something on the vaccum body and is creating the noise. Maybe transmission? Is this normal, or is it something I should be concerned about? Thanks for your help!

Try new belt yours may be slipping ... Kirby G5 Bagged Upright Vacuum

G5 Kirby. Works in Neutral fine. When Drive is engaged and I push forward, the wheels do not rotate forwards, however on the pullback stroke the wheels rotate backwards. What causes this? Something is clearly in the wrong position, so a diagram showing the correct position of the part that is affected would be useful.

Hello, anjeI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ta ... Kirby G4 Bagged Upright Vacuum

On my Hoover Savvy U8174-900 on carpet setting, the brush spins when I pull the vacuum towards me, but stops when I push it forward. Belt is tight and fine.

Hoover savvys have two very common problems that cause this. The first and most obvious is the belt that you checked already. Many times the belt is tight but those particular belts have teeth and should you lose any teeth on the brushroller OR th ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?

Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums

The beater bar moves when I push the vaccum forward but it just drags when I pull it back, but when I flip it over to have a look it easily turns both ways. How do I fix this?

The belt is stretched that is why it is doing that. You need to replace the belt. Here is a link to the belt you need and the manual which has instructions: ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

When i am vacuuming my carpet....it sucks the dirt up when i am pushing it forward, but when i pull it back, the dirt comes back out on the carpet

This is due to a loss of suction. The roller brush sweeps the dirt to the hose area, but with no suction, when you pull the vacuum back, the brush just kicks the dirt back out. This is most likely due to a clog in part of the hose system.\015 ... Vacuums

When I turn the carpet switch on for Shark Navigator, it will grab the carpet when I push forward, but will not when I pull back. Any ideas what the p? I cleaned the brush roller of all hair/fuzz and no change.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Help Our Dyson does not pull itself or self-propel, and you can't push it forward. ANy suggestions?

Dyson vacuums are not self propelled. and if you cannot push it on your carpet then the pile of your carpe is more than what the vacuum can handle. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My kirby vaccum has tech drive and it is stuck in reverse. The wheels spin backwards up lock up when I push it forward

... Kirby Ultimate G Bagged Upright Vacuum

Can't seem to pick up small items like lemon pips with Kirby G5. It just runs over them or pushes them backwards and forwards.

It sounds like your belt is broken, OR your beater bar is rotating but has not been adjusted downward to reach the carpet pile. Check by running the vacuum and looking to see if the beater is moving. ... Kirby G5 Bagged Upright Vacuum

The handle will not stay connected. You can push But when you pull back, it separates right above the off /on switch

There may be damage to where the wand connects to the back of the vacuum cleaner - you should see two grooves on the wand and two on the spine of the vac where the wand slides into - if you have any damage to either side, the wand won't click into pl ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My dyson ball vac bounces when I pull it backwards. It works fine when I push it forward.

They bounce because they spin backwards try to pull back slower. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Why is my kirby shaking when I push it forward

... Vacuums

My Kirby Sentria makes a clicking sound when it is pushed or pulled. It is coming from the region of the rear wheels. Any suggestions?

... Kirby Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0638 seconds